Tannoy Car Speaker IQ 10 15 User Manual

iQ SERIES  
PERFORMANCE DATA AND HARDWARE INFO  
iQ 10/15  
 
Dimensions  
540.0  
680.0  
1116.0  
 
SECUR ET – VEB Eyebolt  
The Tannoy iQ 10/15 loudspeaker can be flown  
with high quality VEB M10 eyebolts with collar to  
BS4278:1984. The loudspeakers are equipped  
with internal steel braces, which also double as  
the flying points, and accept VEB M10 eyebolts.  
To install the VEB M10 eyebolts remove the  
original M10 counter sunk screws from the  
locations you wish to install the VEB M10  
eyebolts. Then replace these counter sunk M10  
screws with the VEB M10 eyebolts. The kelping  
brackets on the rear of the cabinet should only  
be used for tilting the loudspeaker to the desired  
angle.  
Important: It is imperative for safety reasons  
that two eyebolts linked to two independently  
fixed straps are used per cabinet.  
Never attempt to use formed eyebolts i.e.  
formed from a steel rod and bent into an eye.  
!
 
SINGLE iQ SUSPENSION TRUSS (By ATM)  
The iQ suspension truss is an economical solution to suspending a single purpose  
loudspeaker array from two or three fixed structural attachment points. The iQ Suspension  
Truss is designed to hold the loudspeakers at the optimum splay angle to optimize cluster  
performance. Most Suspension Trusses are equipped with two suspension rails with multiple  
attachment holes that travel from front to back across the top of the array, allowing  
manipulation of the center of gravity of the cluster to achieve down tilt without a pull strap.  
Features:  
Optimized fixed splay angle  
Adjustable tilt  
Fast multiple enclosure rigging system  
Economical  
Low profile, clean looking array  
iQ Suspension Truss  
The iQ Suspension Truss is a "semi-custom" product line that is built to order. Please contact  
your Tannoy or ATM Fly-Ware dealer with the loudspeaker model numbers along with the  
array application.  
Full assembly instructions for the iQ Suspension Truss accompany the product.  
 
Typical Suspension Truss applications –  
2 x iQ 10/15  
2 x iQ 10C & 2 x iQ 10/15  
 
Performance Data  
FREQUENCY RESPONSE  
Anechoic System Frequency Response, 1 watt (MF/HF) @ 1 metre on axis  
INPUT IMPEDANCE  
Impedance (Passive MF/HF only)  
 
High Frequency (Tri-amp option)  
Anechoic Frequency Response, 1 watt (HF) @ 1 metre on axis  
Impedance (HF only)  
 
Mid Frequency (Tri-amp option)  
Anechoic Frequency Response, 1 watt (MF) @ 1 metre on axis  
Impedance (MF only)  
A comprehensive range of measurements including off axis frequency response curves, oc
octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Easedata can be  
 
Technical Specifications  
Frequency Response (1) +/- 3dB  
-10dB Point  
49Hz - 19kHz  
43Hz  
Nominal Dispersion  
Driver Compliment  
60o x 40 o (H x V)  
MF/HF – 1 x 250mm (10”) PowerDual™  
LF -  
1 x 380mm (15”)  
Configurations  
Bi-amp (standard) - LF & Passive MF/HF  
Tri-amp (optional)  
Components  
LF  
Midrange  
High Frequency  
Frequency Band (3)  
Sensitivity (1)  
43Hz – 180Hz  
101dB  
180Hz – 2.77kHz  
107dB  
2.77kHz – 19kHz  
110dB  
Power Handling (2)  
400W (average)  
175W (average)  
50W (average)  
800W (programme) 350W (programme) 100W (programme)  
1600W (Peak)  
700W (peak)  
200W (peak)  
Impedance  
8  
16Ω  
16Ω  
Maximum SPL (3)  
127dB (average)  
133 (peak)  
129dB (average)  
135dB (peak)  
127dB (average)  
133dB (peak)  
DI Averaged (PCQ)  
@ 1kHz (ISO)  
@ 2kHz (ISO)  
@ 4kHz (ISO)  
@ 8kHz (ISO)  
@ 16kHz (ISO)  
11.0, 500 Hz - 16 kHz  
12.6  
12.2  
9.5  
11.5  
12.3  
Q Averaged (PCQ)  
@ 1kHz (ISO)  
@ 2kHz (ISO)  
@ 4kHz (ISO)  
@ 8kHz (ISO)  
@ 16kHz (ISO)  
13.5, 500 Hz - 16 kHz  
18.3  
16.7  
8.8  
14  
16.9  
Crossover  
Active 180Hz, Passive 2.6kHz (standard model)  
4th order high pass, 4th order low pass  
Enclosure  
Finish  
18mm multi-ply birch plywood  
Textured black paint (optional in white)  
Foam covered, powder coated perforated steel  
Protective Grille  
Connectors  
2 x Speakon NL4MP in/out (standard model)  
4 x Speakon NL4MP (optional tri-amp model)  
Fittings  
8 x M10 inserts & 2 pullback points  
4 x Recessed Carrying handles  
Dimensions  
Weight  
1116mm x 680mm x 540mm  
(43 15/16” x 26 ¾” x 21 ¼”)  
69kg (152.1 lbs)  
NOTES:  
(1) Average over stated bandwidth. Measured at 1m on axis.  
(2) Long term power handling capacity as defined in EIA standard RS - 426A.  
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber  
The iQ 10/15 is designed for use with the Tannoy TDX1 & TDX2 digital system controller, which provide a preset configuration of  
Crossover frequencies, relative output levels, and system equalization for optimum performance. Should you intend using an alternative  
Loudspeaker management system, these parameters can be accessed from the Tannoy website – www.tannoy.com - or can be found in this  
IQ 10/15 user manual.  
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the publish  
which Tannoy reserves the right to alter without prior notice.  
Please verify the latest specifications when dealing with critical applications.  
Unique Funktion One Axhead Technology (UK patent number GB2270606) is incorporated into  
Tannoy iQ Series SuperDualTM products by agreement with Funkton One Research  
 
iQ 10/15 Service Parts and Accessories  
Part Number Description  
7900 0607  
7900 0609  
7900 0608  
7900 0610  
Driver Kit Type 2519 (MF)  
Recone Kit Type 2519 (MF)  
Driver Kit Type 0278 (HF)  
Diaphragm Type 0278 (HF)  
8001 2820  
VEB – Secur ET – Eyebolts M10  
8000 3630  
8000 3631  
8000 3632  
TDX1 Digital System Controller 60-250V – UK  
TDX1 Digital System Controller 60-250V – EUR  
TDX1 Digital System Controller 60-250V – USA  
8000 0727  
8000 0728  
8000 0729  
TDX2 Digital loudspeaker management system 60-250V - UK  
TDX2 Digital loudspeaker management system 60-250V - EUR  
TDX2 Digital loudspeaker management system 60-250V – USA  
Warranty  
No maintenance of the iQ 10/15 loudspeaker is necessary.  
All Tannoy professional loudspeaker products are covered by a 5 year warranty from  
the date of manufacture subject to the absence of misuse, overload or accidental  
damage. Claims will not be considered is the serial number has been altered or  
removed. A Tannoy Professional dealer or service agent should only carry out work  
under warranty. This warranty in no way affects your statutory rights. For further  
information, please contact your dealer or distributor in your country. If you cannot  
locate your distributor, please contact Customer Services, Tannoy Ltd at the address  
given below.  
Customer Services  
Tannoy Ltd.  
Coatbridge  
ML5 4TF  
Scotland  
Telephone:  
Fax:  
01236 420199  
+44 1236 420199  
01236 428230  
(National)  
(International)  
(National)  
+44 1236 428230  
(International)  
E-Mail:  
Website:  
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION  
Our policy commits us to incorporating improvements to our products through  
continuous research and development. Please confirm current specifications for  
critical applications with your supplier.  
 
Declaration of Conformity  
The following apparatus is/are manufactured in the United Kingdom  
by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland,  
ML5 4TF and conform(s) to the protection requirements of the  
European Electromagnetic Compatibility Standards and Directives  
relevant to Domestic Electrical Equipment. The apparatus is  
designed and constructed such that electromagnetic disturbances  
generated do not exceed levels allowing radio and  
telecommunications equipment and other apparatus to operate as  
intended, and, the apparatus has an adequate level of intrinsic  
immunity to electromagnetic disturbance to enable operation as  
specified and intended. This Equipment conforms to the  
requirements of the EMC Directive 89/336/EEC, amended by  
92/31/EEC and 93/68/EEC and the requirements of the low voltage  
directive 73/23/EEC, amended by 93/68/EEC.  
Details of the Apparatus:  
Tannoy Contractor Loudspeaker  
Model Number: iQ10/15  
Associated Technical File:  
Applicable Standards:  
EMCIQ10/15  
EN 55103 –1:1996 Emission  
EN 55103 –2:1996 Immunity  
EN 60065:1993  
Electrical Safety:  
Signed:  
Position:  
Engineering Director – Professional Products  
Tannoy Professional  
Date:  
11/10/2004  
For Tannoy Ltd  
 

Sharp Camcorder VL A10H User Manual
Sharp Camcorder VL NZ100S User Manual
Sharp MiniDisc Player MD MT821 User Manual
SonicWALL Microscope Magnifier 581 User Manual
Sony Car Stereo System CDX L430X User Manual
Sony Portable CD Player D EJ610 User Manual
Sony Printer SVM 25LW User Manual
Spalding Fitness Equipment 211999B User Manual
Star Micronics Printer LC24 20 User Manual
Sub Zero Cookware CTWH30 User Manual