Eiki Projector AH 55001 User Manual

Securing screws  
LAMP UNIT (LAMP/CAGE MODULE)  
FOR PROJECTOR  
3 Remove the lamp unit.  
• Loosen the securing screws (two for each lamp)  
from the lamp unit. Hold the lamp unit by the  
handle and pull it in the direction of the arrow.  
At this time, keep the lamp unit horizontal and  
do not tilt it.  
MODEL  
AH-55001  
INSTALLATION MANUAL  
CAUTION:  
Handle  
4 Insert the new lamp unit.  
• Potential hazard of glass particles if lamp ruptures. Please have an EIKI Authorized Dealer or Service Center  
replace lamp if rupture occurs.  
• Do not remove the lamp unit directly after operation of the projector.The lamp may be extremely hot.Wait at  
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before  
removing the lamp unit.  
• Fully insert the lamp unit into the lamp unit com-  
partment. Press the handles back to their posi-  
tions, and tighten the securing screws.  
It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi-  
cant deterioration in the picture and color quality.The lamp life (percentage) can be checked with the on-screen display.  
5 Replace the lamp unit cover.  
• Slide the lamp unit cover to the position where  
the indicator “|” of the lamp cover unit and the  
\” of the projector will meet to close the cover.  
Then tighten the user service screw to secure  
the lamp unit cover.  
Compartment  
for  
Lamp 2  
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information  
Compartment  
for  
Lamp 1  
U.S.A. ONLY  
AH-55001  
STANDBY-ON button  
Removing and Installing the  
Lamp Unit  
Info  
• If the lamp unit and lamp unit cover are not cor-  
rectly installed, the power will not turn on, even if  
the power cord is connected to the projector.  
Warning!  
Do not remove the lamp unit from the projector right  
after use. The lamp and parts around the lamp will  
be very hot and may cause burn or injury.  
User service screw  
Info  
Resetting the Lamp Timer  
Make sure the lamp unit is removed using the  
handle. Make sure the glass surface of the lamp  
unit or the inside of the projector are not touched.  
To avoid injury to yourself and damage to the lamp,  
make sure you carefully follow the steps below.  
Do not loosen other screws except for the lamp unit  
cover and lamp unit.  
Reset the lamp timer after replacing the lamp.  
Info  
• Make sure to reset the lamp timer only when re-  
placing the lamp. If you reset the lamp timer and  
continue to use the same lamp, this may cause the  
lamp to become damaged or explode.  
STANDBY-ON button  
1 Press STANDBY-ON on the projec-  
1 Connect the power cord.  
Power cord  
tor or on the remote control to put the  
Plug the power cord into the AC socket of the projector.  
ENTER button  
projector into standby mode.  
Disconnect the power cord and unplug the  
power cord from the AC socket after the cool-  
ing fan stops.  
The cooling fan may continue to run for a while  
even after the power cord is removed.  
Leave the lamp until it has fully cooled down  
(about 1 hour).  
\,", | buttons  
2 Reset the lamp timer.  
2
For Lamp 1  
• When you reset the timer, while simultaneously  
holding down \, " and ENTER, press  
STANDBY-ON on the projector.  
• “LAMP1 0000H” is displayed, indicating that the  
lamp timer is reset.  
2 Remove the lamp unit cover.  
Loosen the user service screw (1) that secures  
the lamp unit cover.Remove the lamp unit cover  
to slide it in the direction of the arrow (2).  
1
For Lamp 2  
User service screw  
• When you reset the timer, while simultaneously  
holding down |, " and ENTER, press  
STANDBY-ON on the projector.  
Power cord  
• “LAMP2 0000H” is displayed, indicating that the  
lamp timer is reset.  
Printed in China  
XXXXXXXXXXXXX  
08PXX-CH-NM  
 

Escali Scale Digital Kitchen Scale User Manual
Estate Clothes Dryer EGD4100S User Manual
First Alert Home Security System 3035DEF User Manual
First Alert Smoke Alarm SA511CN2 3ST User Manual
Fisher Price Baby Toy 73457 User Manual
Fisher Price Motorized Toy Car H0150 User Manual
Fujitsu Cell Phone Accessories MB3891 User Manual
GE Oven PT960BM User Manual
Gianni Industries Door DG 15LD User Manual
Goldstar VCR R E21M User Manual