Accusplit Fitness Electronics AE140XL User Manual

ACCUSPLIT® EAGLE  
AE140XL  
PEDOMETER  
ACCUSPLIT, Inc.  
3090 Independence Drive, Suite 148  
Livermore, CA 94551 USA  
800-935-1996 • 925-290-1900 • FAX 925-290-1930  
www.ACCUSPLIT.com • support@ACCUSPLIT.com  
Eat Right! Walk More! Live Well!  
e ACCUSPLIT Lifestyle  
970-086  
Nov 07  
Operating Instructions  
Functions  
Key Features  
Step counter.  
Built around the Japanese-made JW200 PedometerEngine™  
Step Sensor, the current gold standard for accuracy.  
Distance in mi or km.  
Extra Large Digits.  
For complete Function Specifications, go to page 24.  
The ACCUSPLIT exclusive case makes this the slimmest  
available pedometer built around the JW200 Step Sensor.  
Chromed, Spring Steel clip resists breakage.  
Case includes two leash slots, for attaching safety leash  
on either side. Made from tough polycarbonate plastic.  
Step filter, can be set from 0-5 steps to further increase  
accuracy.  
2
3
HOWTO OPENYOUR PEDOMETER  
See diagrams at right.  
USE IT NOW!  
Your pedometer is preset with standardized settings  
that allow you to use it now!You can customize the  
settings later. Skip to pages 13-16 to use it now!  
The cover must be closed for the  
pedometer to work.  
SETTING UPYOUR PEDOMETER  
Its a good idea to set up your pedometer before first using it.  
To record your distance accurately, you will need to set your  
stride length.  
See page 9 when you are ready to set up your unit.  
4
5
Getting Acquainted  
Mode  
indicator  
Press the MODE button to cycle through the display  
modes (Steps and distance.)  
See page 16 and Specifications for details.  
DIGI-WALKERXL.COM  
DIST  
Steps  
Counted  
STEP  
SET  
The RESET button sets your counts back to zero.  
See page 17 for details.  
MODES  
STEP: STEP mode shows step count.  
DIST: DISTANCE mode shows distance traveled (mi/km).  
MODE Button  
140  
XL  
JW200  
S3-  
S1,S2,S4  
S3+  
RESET Button (yellow)  
6
7
 
RESETTINGYOUR PEDOMETER  
VIEWINGYOUR RESULTS  
Most people prefer to reset counts daily.To reset your counts:  
From STEP or DISTANCE mode, press and hold the yellow  
RESET button for at least 2 seconds.You’ll see the values all  
go back to zero.  
Once you put on your pedometer with the cover closed, it  
will automatically begin to record your steps, activity time,  
and distance. Repeatedly press the MODE button to cycle  
through the pedometer modes:  
STEPS g DISTANCE g STEPS  
Distance is counted automatically whenever steps are being  
counted.  
DISTANCE is simply stride length x steps.  
Note: For extra accuracy, the default Step Filter Setting is 1.  
See page 19 to learn more.  
16  
17  
OTHER SETTINGS  
The Step Filter and Unit of Measurement settings are  
accessed through a special “deep set” mode.  
CHANGING STEP FILTER SETTING  
While the JW200 PedometerEngine™ Step Sensor is  
extremely accurate, some people like to have the ability to  
filter out false steps. Therefore, the unit has a variable setting  
step filter, to allow fine-tuning to your specific preferences.  
You can set the value to any value from 0 – 5 steps. For  
example, if the filter is set to “3, the unit will wait to start  
counting steps until more than three steps have been taken in  
less than five seconds.  
To enter this mode, press and hold the S1 button for 4  
seconds.The screen will display a single digit. From within  
Deep Set mode, press the S2 button to cycle back and forth  
between the Step Filter set point and Choice of Unit System.  
Press S3+ (MODE) or S3– (RESET) to change the Step Filter  
Setting.  
18  
19  
DIGI-WALKERXL.COM  
CHANGING UNITS (English vs. Metric)  
Can be set  
from 0-5  
steps  
STEP  
DIST  
SET  
The Pedometer can display either in English units (in, mi, and lb  
- this is the default), or in Metric units (cm, km, and kg). From within  
Deep Set mode (see pg. 18), press the S2 button to cycle back and  
forth between setting the Step Filter set point and Choice of Unit  
System.The unit will show either “US” or “EU” (for European Union)  
depending on the unit system chosen. If you change units after using  
the pedometer, the unit will convert all of your data into the new unit  
system when you exit Deep Set model.You can check to see which  
system of units you are using by seeing which measurement units  
are displayed on the Stride and Weight setting screens.  
“US” (English)  
or “EU” (Metric)  
DIGI-WALKERXL.COM  
140  
XL  
STEP  
DIST  
SET  
JW200  
S3-  
S1,S2,S4  
S3+  
Set Step Filter set point  
Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.  
Press and hold S4 for 2 seconds to exit Deep Set Mode.  
140  
XL  
JW200  
Note:The unit will save any changes and exit set mode after 30  
S3-  
S1,S2,S4  
S3+  
seconds unattended.  
Set measurement mode  
20  
21  
To replace the battery:  
REPLACINGTHE BATTERY AND MASTER RESET  
When the display starts to dim or goes blank, it is time to  
replace the battery.  
1. Insert a coin into the slot on the  
bottom of the case, and twist to  
loosen the faceplate. Remove  
faceplate and set aside.  
If the display is not uniformly dim or blank, and appears to  
display “erroneous data, do a Master Reset by pressing all  
3 buttons simultaneously for 3 seconds and then release.  
The display should go blank, then turn all segments on, then  
display 0 steps in Step Mode.  
2. Locate the battery holder as seen  
Battery  
on sketch. Pull out the old battery,  
and push a new LR-44 battery into the holder,  
with positive terminal (+) facing up.  
Note: All the settings will return to their default setting values.  
If you need to change the battery, the settings will also revert  
to default settings.  
3. Snap faceplate back into place, hooking the bottom  
two tabs first, then closing by pressing together at the  
top two tabs.  
22  
23  
 
SPECIFICATIONS, FEATURES, and FUNCTIONS  
Description of Functions  
Email (preferred)  
User  
REGISTER NOW Please return  
your AE140XL Registration to  
the Repair Center address in the  
warranty, and we will let you know  
about future products.  
Counts Steps up to 99,999 then rollover.  
Counts distance traveled during step activity, up to  
999.99 mi or km, then rollover. Automatically counts  
whenever step activity is occurring.  
Adjustable stride length for greater distance accuracy  
(default setting is 21 in/53 cm, but can be set from 12-72 in  
(30-180 cm), in 0.25 in / 1 cm increments.  
Adjustable Step Filter (default setting is 1 step, but can  
be set from 0-5 steps) to increase step count accuracy.  
Switchable between English and Metric units, without  
losing data (default setting is English units).  
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY  
Free service for first year of ownership;  
$12 fee for service thereafter. See label inside unit for date.  
24  
25  
INDEX  
Battery, replacing . . . . 22-23  
Current days results,  
viewing . . . . . . . . . . . . . .16  
Setting Mode, exiting . . . .12  
Open your pedometer . . . .4  
Safety Leash . . . . . . . . 14-15  
Setting up pedometer. . 8-12  
Step Filter Setting,  
change . . . . . . . . . . . 18-19  
Stride Length,  
setting. . . . . . . . . . . . . 8-12  
Unit of measure,  
changing. . . . . . . . . . 18-21  
Wearing pedometer . . . . .13  
Warranty . . . . . . . . . . . . . .25  
26  
27  
 

3Com Network Card 10 100BASE T4 User Manual
3M Musical Instrument Amplifier KD45 User Manual
Aiwa MP3 Player CSD FD79 User Manual
AKG Acoustics Conference Phone CS 5 User Manual
American DJ DJ Equipment Flash Tube Buffer User Manual
Atlona TV Cables ATP 14009 User Manual
Audiovox Automobile Alarm APS 255 User Manual
Axis Communications Security Camera Axis 232D User Manual
Axxess Interface Automobile Parts Automobile Parts User Manual
BB Electronics Switch EIP308 User Manual