AGFA Digital Camera 505 X User Manual

Thank you for purchasing this AgfaPhoto digital camera. Please read these operating instructions  
carefully in order to use the digital camera correctly. Keep the instructions in a safe place after read-  
ing so that you can refer to them later.  
Notice: this User’s Manual has been written for the following camera models: AgfaPhoto  
sensor 500-X, AgfaPhoto sensor 505-X and AgfaPhoto sensor 510-X.  
Precautions  
Before using the camera, please ensure that you read and understand the safety precautions de-  
scribed below. Always ensure that the camera is operated correctly.  
Do not point the camera directly into the sun or other intense light sources which could damage  
your eyesight.  
Do not try to open the case of the camera or attempt to modify this camera in any way. High-voltage  
internal components create the risk of electric shock when exposed. Maintenance and repairs should  
be carried out only by authorized service providers.  
Do not fire the flash too close to the eyes of animals or people, especially young children. Eye damage  
may result. In particular, keep at least one meter away from infants when using the flash.  
Keep the camera away from water and other liquids. Do not use the camera with wet hands. Never  
use the camera in the rain or snow. Moisture creates the danger of electric shock.  
Keep the camera and its accessories out of the reach of children and animals to prevent accidents  
or damage to the camera.  
If you notice smoke or a strange odor coming from the camera, turn the power off immediately. Take  
the camera to the nearest authorized service center for repair. Never attempt to repair the camera  
on your own.  
Use only the recommended power accessories. Use of power sources not expressly recommended  
for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or  
other hazards.  
 
Parts of the Camera  
ꢀ. Flash  
ꢁ. Selftimer lamp  
ꢂ. Lens  
4. Operation lamp  
5. LCD display  
6. Playback button  
Five-way control button  
7. OK/Enter button (vertically)  
8. Right  
9. Down  
ꢀ0. Up  
ꢀꢀ. Left  
12. MENU button  
 
ꢀꢂ. Shutter button  
ꢀ4. Mode button  
ꢀ5. Power button  
ꢀ6. Microphone  
ꢀ7. Strap mount  
ꢀ8. Battery cover  
ꢀ9. USB jack  
ꢁ0. Tripod socket  
Attaching the Strap  
Attach the strap to your camera as shown in the image.  
Caution  
Do not swing the camera around by the strap  
4
 
Inserting the Batteries  
The camera is powered by two AAA-size alkaline batteries or rechargeable NiMH batteries.  
Open the battery cover.  
1
2
Slide the battery cover in the direction indicated by the arrows.  
Insert the batteries.  
Insert two AAA-size batteries with the positive (+) and negative  
(-) poles matching the directions indicated inside the battery  
compartment.  
Close the battery cover.  
3
Turning Power On & Off  
1
2
Press the Power button (ꢀ) to turn on the camera in the Capture  
mode. The power turns on and the LED (2) lights red.  
Press the Power button (1) again to turn the power off. The power turns off and the LED turns  
off.  
5
 
Changing the Mode  
You can record images and voices in the REC mode and use the Playback mode to replay, delete or  
edit images on the LCD monitor.  
Switching between REC and Playback Mode  
In REC mode, press the Playback button (ꢁ) to switch to the  
Playback mode.  
In Playback mode, press the Playback button (ꢁ) to switch to the  
REC mode.  
Selecting the REC Mode  
Press the Power button to enter the Capture mode.  
1
2
If the camera is in Playback mode, press the Playback button to change to REC mode.  
Press the Mode button (1) to change the REC mode.  
Each time the Mode button is pressed the REC mode icon changes. It includes three modes in  
REC mode: Capture mode, Video mode and Audio mode.  
6
 
Display  
Title  
Capture mode  
Description  
For taking still photos.  
Video mode  
For recording movie clips.  
Audio mode  
For recording audio files.  
Caution  
The Mode button will not work when the camera is in Playback mode.  
Using the Menu in REC Mode  
When a menu is displayed, the five-way control button is used to make the desired settings. The  
Audio mode does not have a menu so the MENU button will not work in Audio mode.  
Capture menu.  
1
Turn the power on, and set the camera to the Capture  
mode  
Open the Capture menu.  
2
3
Press the MENU button (2) to display the menu.  
Select an item.  
Press  
or  
on the five-way control button (1) to select  
an item.  
Change the setting.  
4
Press  
on the five-way control button (1) to launch the  
submenu. Press  
to change the setting.  
or  
on the five-way control button (1)  
7
 
5
Press OK/Enter on the five-way control button (1) to save the settings and finally press the  
MENU button (2) to close the menu  
Using the Menu in Playback Mode  
When a menu is displayed, the five-way control button is used to make the desired settings.  
Using the Menu in Playback Mode  
Turn the power on and set the camera to the Playback  
1
mode  
Open the Playback menu.  
2
3
Press the Menu button (ꢁ) to display the menu.  
Select an item.  
Press  
item.  
or  
on the five-way control button (1) to select an  
Change the setting.  
4
5
Press  
on the five-way control button (1) to launch the  
submenu. Press  
or  
on the five-way control button (1) to change the setting.  
Press OK/Enter (1) to save the settings and finally press the Menu button (2) to close the menu.  
Caution  
If the item in the menu list is gray it means this item doesn’t work in this file format.  
8
 
Setting the Display Language / Date & Time  
When using the camera for the first time after purchasing it, be sure to choose a language and set the  
date & time before using the camera.  
Setting Display Language  
Turn the power on, and set the camera to the Setup Menu.  
1
Select [Language].  
2
Press  
the submenu.  
or  
to select [Language] then press  
to launch  
Select a language.  
3
4
Press  
or  
on the five-way control button to select a  
language and press OK/Enter button to apply the setting.  
Press the MENU button to close the menu.  
9
 
Setup Menu  
Turn the power on and set the camera to the REC or  
Playback mode.  
1
2
Press the MENU button (2) to open the REC or Playback  
menu. The menu displayed depends on whether you are in the  
REC mode or the Playback mode.  
Open the Setup menu.  
3
4
5
6
Press  
on the five-way control button (1) to select [Setup] to  
display the Setup menu.  
Select an item.  
Press  
or  
on the five-way control button (1) to select a menu item then press  
on the  
five-way control button (1) to launch the submenu.  
Change the setting.  
Press  
apply the setting.  
or  
on the five-way control button (1) to select an option and press OK/Enter (1) to  
Press the MENU button (2) to close the menu.  
ꢀ0  
 
Deleting a Single File  
Turn the power on, and set the camera to the Playback mode  
1
2
3
Select the file you want to delete.When the file is shown in full screen, press  
the five-way control button to select the file you want to delete.  
or  
on  
Open the menu.  
Press the MENU button, then press  
or  
on the five-way control button to select [Delete  
current].  
Delete the file.  
4
Press  
on the five-way control button to delete the file.  
Connecting the Camera to a TV  
You can display recorded images on a television with the supplied AV cable.  
Set the TV-out to match the TV system that you are using.  
1
Turn off the camera and the TV.  
2
Use the supplied AV cable to connect the camera to the TV set.  
3
4
5
Then turn on the camera and the TV.  
Set the TV input signal to Video In.  
Refer to the documentation included with your TV for more information.  
Display on TV.  
Everything that would normally appear on the camera’s LCD screen, such as photos and video  
clip playback, slide shows and image or video capture, will appear on the TV. The camera’s  
LCD screen turns off.  
ꢀꢀ  
 
Connecting the Camera to a PC  
There are two ways to download files from the camera’s internal memory or memory card to a com-  
puter:  
By inserting the memory card into a card reader  
By connecting the camera to a computer using the supplied USB cable.  
Using a Card Reader (not included)  
1
2
3
Eject the memory card from the camera and insert it into a card  
reader that is connected to a computer.  
Open [My Computer] or [Windows Explorer] and double-click the  
removable disk icon that represents the memory card.  
Copy images from the card into a directory of your choice on the  
computer’s hard disk.  
ꢀꢁ  
 
Connecting the Camera to a PC with the USB Cable  
To download photos from the camera  
1
Connect the supplied USB cable to the computer’s USB port and turn on the camera. A  
message “Mass Storage” or “PC Camera” appears on the screen when connection to the  
computer has been successfully completed. Press the playback button to switch the camera  
mode between mass storage and PC camera. To download photos please select “Mass  
Storage” mode.  
2
3
Open [My Computer] or [Windows Explorer]. A «Removable Disk» appears in the drive list.  
Double-click the «Removable Disk» icon to view its contents. Files stored on the camera are  
located in the folder named «DCIM».  
Copy the photos or files to your computer.  
ꢀꢂ  
 
Customer care  
More information on the complete AgfaPhoto digital camera product range can be found under www.  
Service & Repair (USA / Canada):  
ꢀ-866 475 ꢁ605  
Support Service (USA / Canada):  
Online Service USA / Canada:  
Service & Repair Hotline (Europe):  
00800 75ꢁ 9ꢁꢀ 00 (from a landline only)  
Service & Support Hotline (Germany):  
0900 1000 042 (1.49 Euro/ min. from a German landline only)  
Online Service / International contact (Not USA / Canada):  
Designed and manufactured by  
plawa-feinwerktechnik GmbH & Co. KG  
Bleichereistraße ꢀ8  
7ꢂ066 Uhingen  
Germany  
AgfaPhoto is used under license of Agfa-Gevaert NV & Co. KG. Agfa-Gevaert NV & Co. KG. does not  
manufacture this product or provide any product warranty or support. For service, support and war-  
ranty information, contact the distributor or manufacturer.  
ꢀ4  
 
Disposal of Waste Equipment by Users in Private Households in the  
European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of  
with your other household waste. Instead, it is your responsibility to dispose of your waste equipment  
by handing it over to a designated collection point for the recycling of waste electrical and electronic  
equipment. The separate collection and recycling of your waste equipment at the time of disposal will  
help to conserve natural resources and ensure that it is recycled in a manner that protects human  
health and the environment. For more information about where you can drop off your waste equip-  
ment for recycling, please contact your local city office, your household waste disposal service or the  
shop where you purchased the product.  
FCC Compliance and Advisory  
This device complies with Part ꢀ5 of the FCC Rules. Operation is subject to the following two condi-  
tions: ꢀ.) this device may not cause harmful interference, and ꢁ.) this device must accept any interfer-  
ence received, including interference that may cause unsatisfactory operation. This equipment has  
been tested and found to comply with the limits for a Class B peripheral, pursuant to Part ꢀ5 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may cause harmful interference to  
radio communication. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the receiver is con-  
nected.  
Consult the dealer or an experienced radio/TV technician for help.  
Any changes or modifications not expressly approved by the party responsible for compliance could  
void the user’s authority to operate the equipment. When shielded interface cables have been  
provided with the product or when specified additional components or accessories have elsewhere  
been designated to be used with the installation of the product, they must be used in order to ensure  
compliance with FCC regulations.  
ꢀ5  
 

ADC Network Router Building Entrance Terminals BET User Manual
AGFA Printer JETI 5024 User Manual
Airlink101 Network Router AR680W User Manual
Aluratek Camera Lens ADMPFB100 User Manual
American Dish Service Dishwasher ADC 66 L R R L User Manual
American Standard Hot Tub ANSI Z 12412 User Manual
ATN Inc Binoculars PVS7 User Manual
Audiovox Camcorder DC500 User Manual
Barco Projector R 9849999 User Manual
Beko Refrigerator GNEV122X User Manual