A s s e m b l y
G u i d e
X6600iNetTV
COMMERCIAL ELLIPTICAL TRAINER
Screwdriver
TOOLS & PARTS INCLUDED
MM
6 Allen Wrench
MM
5 Allen Wrench
MM
8 L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty:1
Link Arm Covers, Qty: 2
Pedal Support Brackets, Qty: 2
Dual Action End Caps, Qty: 2
Color-coded Hardware Bags
Owner’s Guide
MM
17 Socket Wrench
Assembly Guide
Warranty Card
CONSOLE BOX
iNetTV Console
Owner’s Guide
MM
10 L-Shaped Wrench
HARDWARE INCLUDED
ORANGE BAG
BLUE BAG
M10x70L CapScrew
Quantity: 2
M8x15L Screw
Quantity: 2
M20x30x1.5T
Wavy Washer
Quantity: 2
M8x80L SocketHead CapScrew
Quantity: 1
M8x10L Screw
Quantity: 4
PINK BAG
MM
6 L-Shaped Wrench
M5x12L Screw
Quantity: 6
FOR SERVICE ONLY
M10 Nut
Quantity: 2
Link Arm Bushing
Quantity: 2
M10x18x2T Washer
Quantity: 4
M5.3x10x1T Washer
Quantity: 4
M49x7 Round Tool
Quantity: 1
M8x30L CapScrew
Quantity: 8
M6x40L CapScrew
M12x60L CapScrew
Quantity: 1
Quantity: 3
M10x40L CapScrew
Quantity: 2
STEP
1
ORANGE BAG
• Place the rubber console mast boot
on the end of the console mast.
• Connect the wire tie that exits the
bottom of the console mast to the
bundle of wires that comes from the
bracket at the top of the frame. Pull the
wire tie and wire harness up through the
console mast while at the same time
inserting the console mast into the frame
bracket.
STEP
1
• Secure the console mast to the frame
with two capscrews (M10 x 70L).
MM
Tighten with the 8 L-shaped Allen
wrench.
• Stabilize the console mast to the
frame with the socket head cap screw
(M10x70L). Tighten with the
MM
10 L-shaped Allen wrench.
• Slide the rubber boot down the
console mast and snap it in place so
it integrates with the side covers.
STEP
2
BLUE BAG
•
Place
a
wavy
washer
(M20x30x1.5t) on the axle located
under the foot plate of the right lower
link arm.
STEP
2
• Slide the axle of the lower link arm
into the bracket located on the top of
the right pedal arm. Secure lower link
arm by attaching the pedal support
bracket and screw (M8x15L) to the
end of the axle. Secure the outside
holes in the bracket to the footplate
with two screws (M8x10L). Tighten
MM
screws with the 5 Allen wrench.
• Repeat the same steps on the left
side.
5
STEP
3
PINK BAG
• Connect the right dual-action arm to
the right console mast rotation
housing, being sure to line up the
holes. Secure the dual action arm in
place with four screws (M8x30L) and
MM
tighten with a 6 T-handled Allen
wrench. Snap the dual action end
cap into place.
• Connect the right lower link arm to
the right dual-action arm by lining up
the holes on the end of each arm.
Slide the Link Arm Bushing into the
hole of the socket joint. Place a
washer (M10.5x18x2t) on the
capscrew (M10x40L) and slide the
capscrew through the hole. Place a
second washer followed by a nut
(M10) on the capscrew and tighten
MM
MM
using the 17 socket wrench and 8
L-shaped Allen wrench.
• Position the link arm cover into
place over the joint of the lower link
arm and dual-action arm. With a
screw (M5x12L) and Phillips
screwdriver, connect the two halves of
the cover through the hole located in
the front of the cover. Attach the cover
to each side of the lower link arm with
the two washers (M5.3x10x1t) and
two screws (M5x12L).
• Repeat these steps on the left side.
STEP
3
6
STEP
4
CONSOLE
• Remove the six mounting screws
from the back of the console with the
Phillips screwdriver. Set the console in
place and secure it to the console
mast with the screws you just
removed. Connect all the wires to the
proper locations in the back of the
console (see diagram).
STEP
4
1
2
3
4
5
6
7
8
9
WIRES
10
12
13
11
14
1 - Co-Axial Cable TV
2 - USB - B
3 - USB - A
4 - VGA (PC Video)
5 - Video IN
6 - Audio - R
7 - Audio - L
8 - Microphone
9 - Heart Rate Reciever 1
10 - Heart Rate Reciever 2
11 - 20 Pin Connector
12 - Power Plug
13 - Miles/Kilometers Switch
14 - Data Port
500 South CP Avenue
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z66EP24-AG1826PRD
AG18.26PRD
REV1
7
|