Go to
CS6919
CS6919-15
CS6919-16
CS6919-17
CS6919-19
CS6919-2
CS6919-25
CS6919-26
CS6919-27
CS6919-29
CS6919-3
CS6919-4
to register your product for
enhanced warranty support
and latest VTech product
news.
DECT 6.0 cordless telephone
BC
User’s manual
supply in your home or office, consult
your dealer or local power company.
9. Do not allow anything to rest on
the power cord. Do not install this
product where the cord may be
walked on.
• If the product has been dropped
and the telephone base and/or
handset has been damaged.
• If the product exhibits a distinct
change in performance.
14. Avoid using a telephone (other than
cordless) during an electrical storm.
There is a remote risk of electric
shock from lightning.
10.Never push objects of any kind into
this product through the slots in the
telephone base or handset because
they may touch dangerous voltage
points or create a short circuit. Never
spill liquid of any kind on the product.
11.To reduce the risk of electric shock,
do not disassemble this product,
but take it to an authorized service
facility. Opening or removing parts of
the telephone base or handset other
than specified access doors may
expose you to dangerous voltages or
other risks. Incorrect reassembling
can cause electric shock when the
product is subsequently used.
12.Do not overload wall outlets and
extension cords.
15. Do not use the telephone to report
a gas leak in the vicinity of the
leak. Under certain circumstances,
a spark may be created when the
adapter is plugged into the power
outlet, or when the handset is
replaced in its cradle. This is a
common event associated with the
closing of any electrical circuit. The
user should not plug the phone
into a power outlet, and should
not put a charged handset into
the cradle, if the phone is located
in an environment containing
concentrations of flammable or
flame-supporting gases, unless there
is adequate ventilation. A spark in
such an environment could create a
fire or explosion. Such environments
might include: medical use of
oxygen without adequate ventilation;
industrial gases (cleaning solvents;
gasoline vapors; etc.); a leak of
natural gas; etc.
13.Unplug this product from the wall
outlet and refer servicing to an
authorized service facility under the
following conditions:
• When the power supply cord or
plug is damaged or frayed.
• If liquid has been spilled onto the
product.
• If the product has been exposed
to rain or water.
• If the product does not operate
normally by following the
16. Only put the handset of your
telephone next to your ear when it is
in normal talk mode.
17. The power adapters are intended to
be correctly oriented in a vertical or
floor mount position. The prongs are
not designed to hold the plug in place
if it is plugged into a ceiling,
operating instructions. Adjust only
those controls that are covered
by the operation instructions.
Improper adjustment of other
controls may result in damage and
often requires extensive work by
an authorized technician to restore
the product to normal operation.
under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
convenient create some limitations.
Telephone calls are transmitted
between the telephone base and the
cordless handset by radio waves,
so there is a possibility that the
cordless telephone conversations
could be intercepted by radio
receiving equipment within range
of the cordless handset. For this
reason, you should not think of
cordless telephone conversations as
being as private as those on corded
telephones.
Battery
• CAUTION: Use Only Supplied
Battery.
• Do not dispose of the battery in a fire.
Check with local waste management
codes for special disposal instructions.
• Do not open or mutilate the battery.
Released electrolyte is corrosive and
may cause burns or injury to the eyes
or skin. The electrolyte may be toxic if
swallowed.
• Exercise care in handling batteries in
order not to create a short circuit with
conductive materials.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified
in this manual.
• Electrical power: The telephone
base of this cordless telephone must
be connected to a working electrical
outlet. The electrical outlet should not
be controlled by a wall switch. Calls
cannot be made from the cordless
handset if the telephone base is
unplugged, switched off or if the
electrical power is interrupted.
• Potential TV interference: Some
cordless telephones operate
Precautions for users of
implanted cardiac pacemakers
Cardiac pacemakers (applies only to
digital cordless telephones):
Wireless Technology Research, LLC
(WTR), an independent research entity,
led a multidisciplinary evaluation of the
interference between portable wireless
telephones and implanted cardiac
pacemakers. Supported by the U.S.
Food and Drug Administration, WTR
recommends to physicians that:
at frequencies that may cause
interference to televisions and
VCRs. To minimize or prevent
such interference, do not place
the telephone base of the cordless
telephone near or on top of a TV or
VCR. If interference is experienced,
moving the cordless telephone farther
away from the TV or VCR often
reduces or eliminates the interference.
• Rechargeable batteries: Exercise
care in handling batteries in order
not to create a short circuit with
conducting material such as rings,
bracelets and keys. The battery or
conductor may overheat and cause
harm. Observe proper polarity
between the battery and the battery
charger.
• Nickel-metal hydride rechargeable
batteries: Dispose of these batteries
in a safe manner. Do not burn or
puncture the battery. Like other
batteries of this type, if burned or
punctured, they could release caustic
material which could cause injury.
Pacemaker patients
• Should keep wireless telephones at
least six inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as
in a breast pocket, when it is turned
ON.
• Should use the wireless telephone at
the ear opposite the pacemaker.
WTR’s evaluation did not identify any
risk to bystanders with pacemakers
from other persons using wireless
telephones.
About cordless telephones
• Privacy: The same features
that make a cordless telephone
Table of contents
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in case it is
necessary to ship your telephone for
warranty service.
NOTE
To purchase replacement batteries or power
adapters, visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or dial
1 (800) 267-7377.
1 set for CS6919/ CS6919-15/
CS6919-16/CS6919-17/CS6919-19
2 sets for CS6919-2/CS6919-25/
CS6919-26/CS6919-27/CS6919-29
3 sets for CS6919-3
4 sets for CS6919-4
1 set for CS6919-2/CS6919-25/
CS6919-26/CS6919-27/CS6919-29
2 sets for CS6919-3
3 sets for CS6919-4
1 set for CS6919/CS6919-15/CS6919-16/
CS6919-17/CS6919-19/CS6919-2/
CS6919-25/CS6919-26/CS6919-27/
CS6919-29/CS6919-3/CS6919-4
Abridged user’s
manual
Important Safety
Instructions
1 set for CS6919/CS6919-15/
CS6919-16/CS6919-17/CS6919-19/
CS6919-2/CS6919-25/CS6919-26/
CS6919-27/CS6919-29/CS6919-3/
CS6919-4
1
5 –
6 –
Overview
• Press repeatedly to show other
dialing options when reviewing a
caller ID log entry.
Handset overview
• Press to start an intercom
conversation or transfer a call (for
multi-handset models only).
a
b
p
7 – Microphone
8 –
o
n
• Mute the microphone during a
c
d
call.
• Delete digits or characters while
using the dialing keys.
• Silence the ringer temporarily
while the handset is ringing.
m
l
9 –
k
j
i
h
• Make or answer a call using the
handset speakerphone.
e
f
g
• During a call, press to switch
between the speakerphone and
the handset earpiece.
10 –
1 – Handset earpiece
2 – LCD display
• While you have set the dial mode
to pulse and on a call, press to
switch to tone dialing temporarily.
3 –
11 –
12 –
• Show the menu.
• Press to add a space when
entering names.
• While in a menu, press to select
an item, or save an entry or
setting.
• Press repeatedly to add or
remove 1 in front of the caller ID
log entry before dialing or saving
it to the phonebook.
• Press and hold to set or dial your
voicemail number.
4 –
• Hang up a call.
• Silence the ringer temporarily
while the handset is ringing.
•
Press and hold to erase the
missed call indicator while the
phone is not in use.
13 –
• Press to return to the previous
menu; or press and hold to return
to idle mode, without making
changes.
• Make or answer a call.
• Answer an incoming call when
you hear a call waiting alert.
2
14 –
15 –
Telephone base overview
• Press repeatedly to review the
redial list.
• Press and hold to insert a dialing
pause while entering a number.
a
b
c
• Review the phonebook when the
phone is not in use.
• Increase the listening volume
during a call.
• Scroll up while in a menu,
phonebook, caller ID log, or
redial list.
• Move the cursor to the right when
entering numbers or names.
1 –
light
• Flashes when there is an
incoming call, or another
telephone sharing the same line
is in use.
• Flashes when handsets are
being deregistered.
• Review the caller ID log when the
phone is not in use.
• On when the handset is in use or
being registered.
• Decrease the listening volume
during a call.
• Scroll down while in a menu,
phonebook, caller ID log, or
redial list.
2 –
• Press to page all system
handsets.
• Move the cursor to the left when
entering numbers or names.
3 – Charging pole
16 –
light
Charger overview
• On when the handset is
charging.
a
1 – Charging pole
3
Telephone base lights
On when the
Display icons overview
The battery icon flashes
when the battery is low
and needs charging.
telephone line is in
use.
On when you
are registering a
handset.
The battery icon animates
when the battery is
charging.
Flashes quickly
when there is an
incoming call.
The handset ringer is off.
There are new voicemail
received from your
telephone service
provider.
Flashes when
another telephone
sharing the same
line is in use.
ECO
NEW
The ECO mode activates
automatically to reduce
power consumption when
the handset is within range
from the telephone base.
Flashes when you
are deregistering all
handsets.
There are new caller ID
log entries.
Handset and Telephone base
lights overview
Handset lights
On when the handset
speakerphone is in
use.
On when the handset
is charging in the
telephone base or
handset charger.
4
Mount the telephone base
Connect
You can choose to connect the telephone
base for desktop usage or wall mounting.
1. Connect the telephone line cord to
the telephone base. Route it through
the wall mount bracket, and then
connect it to the wall jack.
NOTES
• Use only the adapters provided.
• Make sure the electrical outlets are not
controlled by wall switches.
• The adapters are intended to be correctly
oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
TIP
• If you subscribe to digital subscriber line
(DSL) high-speed Internet service through
your telephone line, make sure you install
a DSL filter (not included) between the
telephone line cord and telephone wall
jack. Contact your DSL service provider
for more information.
2 Align and place the wall mount
bracket on the standard wall plate.
A
Connect the telephone base
Connect the charger
5
3. Align and place the telephone base on
the wall mount bracket. Slide it down
until it clicks securely in place.
Install and charge the battery
Install the battery as shown below.
NOTES
• Use only the battery provided.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
• If the handset will not be used for a long
time, disconnect and remove the battery to
prevent possible leakage.
4. Connect the power adapter.
THIS SIDE UP
6
Charge the battery
Place the handset in the telephone base
or the charger to charge.
The screen
shows
HANDSET X.
The battery is To keep
charged.
the battery
charged,
place it in the
telephone
base or
charger when
not in use.
When it is fully charged, you can expect
the following performance:
Operation
Operating time
While in handset
use (talking*)
Seven hours
While in
Three and a half
speakerphone mode hours
(talking*)
While not in use
(standby**)
Five days
Once you have installed the battery,
the handset LCD display indicates the
battery status (see the table below).
* Operating times vary depending on your actual
use and the age of the battery.
** Handset is not charging or in use.
NOTES
• For best performance, keep the handset in
the telephone base or charger when not
in use.
• The battery is fully charged after 12 hours
of continuous charging.
• If you place the handset in the telephone
base or the charger without plugging
in the battery, the screen displays
No battery.
Battery
indicators
Battery
status
Action
The screen
is blank, or
shows Put
in charger
and
The battery
has no
Charge
without
charge or
very little
charge. The
handset
interruption
(at least 30
minutes).
flashes.
cannot be
used.
The screen
The battery
has enough
Charge
shows Low
without
battery and charge to be
flashes.
interruption
(at least 30
minutes).
used for a
short time.
7
Operating range
Before use
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
telephone base can communicate over
only a certain distance - which can
vary with the locations of the telephone
base and handset, the weather, and the
layout of your home or office.
After you install your telephone or
power returns following a power outage,
the handset will prompt you to set the
date and time.
Set date and time
1. Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
When the handset is out of range, the
handset displays Out of range or no pwr
at base.
2. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press or to choose AM or PM.
If there is a call while the handset is
out of range, it may not ring, or if it
does ring, the call may not connect well
when you press . Move closer to the
telephone base, and then press
3. Press SELECT to save.
Check for dial tone
Press . If you hear a dial tone, the
installation is successful.
to answer the call. If the handset
moves out of range during a telephone
conversation, there may be interference.
To improve reception, move closer to the
telephone base.
If you do not hear a dial tone:
• Make sure the installation procedures
described above are properly done.
• It may be a wiring problem. If you
have changed your telephone
service to digital service from a
cable company or a VoIP service
provider, the telephone line may need
to be rewired to allow all existing
telephone jacks to work. Contact your
cable/VoIP service provider for more
information.
8
Set date and time
1. Press MENU when the handset is not
Configure your telephone
Using the handset menu
in use.
1. Press MENU when the phone is not
2. Press or to choose Set date/time,
in use.
and then press SELECT.
2. Press or until the screen displays
the desired feature menu.
3. Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
3. Press SELECT to enter that menu.
4. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press or to choose AM or PM.
• To return to the previous menu, press
CANCEL on the handset.
• To return to idle mode, press and hold
5. Press SELECT to save. Then the
handset returns to the previous
menu. You hear a confirmation tone.
CANCEL on the handset.
Set language
The LCD language is preset to English.
You can select English, French or
Spanish to be used in all screen displays.
Home area code
If you dial your local calls using only
seven digits (area code not required),
you can program your home area code
so that when you receive a call within
your local area, the telephone number
is automatically stored without the area
code in the caller ID log.
1. Press MENU when the handset is not
in use.
2. Press or to choose Settings,
and then press SELECT.
3. Press SELECT to choose LCD
1. Press MENU when the phone is not
language.
in use.
4. Press or to choose English,
Français or Español, and then press
SELECT. Then the handset returns
to the previous menu. You hear a
confirmation tone.
2. Press or to choose Settings, and
then press SELECT.
3. Press or to choose Home area
code, and then press SELECT.
4. Use the dialing keys to enter a
three-digit home area code.
5. Press SELECT to save your
selection. Then the handset returns
to the previous menu. You hear a
confirmation tone.
NOTE
•
If, in the future, your telephone service
provider requires you to dial the area
code when making a local call, or, if you
move to a location that requires it, delete
the home area code you have already
programmed, following the steps above.
After you have deleted the home area
code, _ _ _ will appear on the display.
9
Dial mode
Telephone Operations
The dial mode is preset to touch-tone
dialing. If you have pulse (rotary)
service, you need to change the dial
mode to pulse dialing before using the
telephone to make a call.
Handset control key panel:
1. Press MENU when the phone is not
in use.
2. Press or to choose Settings,
and then press SELECT.
3. Press or to choose Dial mode,
and then press SELECT.
4. Press or to choose Touch-tone
or Pulse.
5. Press SELECT to save your
selection. Then the handset returns
to the previous menu. You hear a
confirmation tone.
Temporary tone dialing
If you have pulse (rotary) service only,
you can switch from pulse to touch-tone
dialing temporarily during a call. This
is useful if you need to send touch-
tone signals to access your telephone
banking or long distance services.
1. During a call, press
.
2. Use the dialing keys to enter the
number. The telephone sends
touch-tone signals. The telephone
automatically returns to pulse dialing
mode after you end the call.
10
Make a call
Volume
During a call, press /VOLUME/ to
adjust the listening volume.
1. Press
or on the handset.
2. When you hear a dial tone, dial the
number.
NOTES
•
•
The handset and speakerphone volume
settings are independent.
• The handset displays Unable to
call if the telephone line is in use.
When the volume reaches the minimum
or maximum setting, you hear two beeps.
NOTES
•
•
The handset shows the elapsed time as
you talk (in hours, minutes and seconds).
Mute
While entering numbers, press and hold
PAUSE to insert a dialing pause
(a p appears).
The mute function allows you to hear
the other party but the other party
cannot hear you.
Predial a call
1. Enter the telephone number.
• During a call, press MUTE. The
handset displays Muted until the
mute function is turned off.
2. Press
or to dial.
• Press MUTE again to resume the
conversation. The handset briefly
displays Microphone on.
NOTES
•
•
•
The handset displays Unable to call if
the telephone line is in use.
The handset shows the elapsed time as
you talk (in hours, minutes and seconds).
Join a call in progress
You can use up to two system handsets
at a time on an outside call.
• When a handset is already on a call,
While entering numbers, press DELETE
or CANCEL to make corrections;
press and hold PAUSE to insert a dialing
pause (a p appears).
press
or on another handset to
join the call.
Answer a call
• Press OFF or place the handset
in the telephone base or handset
charger to exit the call. The call
continues until all handsets hang up.
Press
,
, or any dialing key (0-9,
) to answer.
or
,
End a call
NOTE
Press OFF on the handset, or place the
handset in the telephone base or
handset charger.
•
If you have paired a DECT 6.0 cordless
headset and speakerphone to the
telephone base, you can also join a call
in progress using the paired device. Refer
to the user’s manuals of the respective
product for more information.
Speakerphone
During a call, press to switch
between the speakerphone
and the handset earpiece. When the
speakerphone is active, the handset
displays Speaker.
11
To access a number from the
phonebook while on a call:
1. Press MENU.
Call waiting
When you subscribe to call waiting
service with your telephone service
provider, you hear an alert tone if there
is an incoming call while you are on
another call.
2. Press SELECT to select Phonebook.
3. Press or to scroll to the desired
entry.
• Press FLASH to put the current call
on hold and take the new call.
• Press FLASH at any time to switch
back and forth between calls.
4. Press SELECT to dial the displayed
number.
To access a number from the
caller ID log while on a call:
1. Press MENU.
If you also subscribe to caller ID
service, it will let you see the name and
telephone number of the caller during
call waiting.
2. Press or to choose Caller ID
log, and then press SELECT.
3. Press or to scroll to the desired
entry.
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provider
if:
4. Press SELECT to dial the displayed
number.
• You have both caller ID and call
waiting, but as separate service (you
may need to combine these service);
To access a number from the
redial list while on a call:
1. Press REDIAL to enter the redial list.
• You have only caller ID service, or
only call waiting service; or
2. Press
,
, or REDIAL repeatedly to
browse to the desired entry.
• You do not subscribe to caller ID or
call waiting services.
3. Press SELECT to dial the displayed
number.
There are fees for caller ID services. In
addition, services may not be available
in all areas.
Chain dialing
Use this feature to initiate a dialing
sequence from numbers stored in the
phonebook, caller ID log or redial list
while you are on a call.
Chain dialing can be useful if you wish
to access other numbers (such as bank
account numbers or access codes)
from the phonebook, caller ID log or
redial list.
12
Find handset
This feature helps you find all system
handsets.
Redial list
Each handset stores the last
10 telephone numbers dialed. Entries
are shown in reverse chronological
order. When there are already
10 entries, the oldest entry is deleted to
make room for the new entry.
To start paging:
• Press /FIND HANDSET on the
telephone base.
All idle handsets ring and display
** Paging **.
Review a redial list entry
1. Press REDIAL to enter the redial list.
To end paging:
• Press /FIND HANDSET again on
2. Press
,
, or REDIAL repeatedly
the telephone base.
to browse until the desired entry
displays.
-OR-
• Press , OFF, or any dialing key
NOTE
(0-9,
or
) on the handset.
,
•
You hear a double beep when you reach
the beginning or end of the redial list.
-OR-
• Place the handset in the telephone
base or charger.
Dial a redial list entry
1. Press REDIAL to enter the redial list.
NOTES
2. Press
,
, or REDIAL repeatedly
• Press MUTE to turn off the ringer of
a handset temporarily. Paging tone
continues on the other handset.
to browse until the desired entry
displays.
3. Press
or to dial.
• Do not press and hold /FIND HANDSET
for more than four seconds. It may lead
to handset deregistration. If the handset
displays To register HS... and ...see
manual, refer to the Frequently asked
questions section to register the handset
back to the telephone base.
-OR-
1. Press
or to take the line.
2. Press REDIAL to enter the redial list.
3. Press , or REDIAL repeatedly
,
to browse until the desired entry
displays.
4. Press SELECT to dial the displayed
number.
Delete a redial list entry
1. Press REDIAL to enter the redial list.
2. Press
,
, or REDIAL repeatedly
to browse until the desired entry
displays.
3. When the handset displays the number
you want to delete, press DELETE.
You hear a confirmation tone.
13
•
You can use four handsets on two pairs
of intercom calls. For example, when four
handsets are used on two pairs of intercom
calls, use the fifth handset for an outside
call.
Multiple handset use
Intercom
Use the intercom feature for
conversations between two handsets.
Your telephone base supports up to
five handsets. You can buy additional
expansion handsets (CS6909) for this
telephone base.
Answer an incoming call during
an intercom call
When you receive an outside call during
an intercom call, there is an alert tone.
1. Press INT on your handset when not
• To answer the outside call, press
.
in use.
The intercom call ends automatically.
• If you have only one handset, your
• To end the intercom call without
answering the outside call, press
OFF. The telephone continues to
ring.
handset displays INT needs 2 HS.
• If you have two handsets, your
handset displays Calling HS X.
• If you have three or more
handsets, your handset displays
Intercom to. Use the dialing keys
to enter a destination handset.
Your handset displays Calling HS X.
Call transfer using intercom
Use the intercom feature to transfer an
outside call to another system handset.
1. During a call, press INT.
The destination handset rings and its
• If you have two handsets, the
outside call is put on hold and your
handset displays Calling HS X.
screen displays HS X is calling.
2. To answer the intercom call, press
,
, INT or any dialing key (0-9,
• If you have three or more
or
) on the destination handset.
handsets, your handset displays
Intercom to. Use the dialing keys
to enter a handset number. The
outside call is put on hold and your
handset displays Calling HS X.
Both handsets now display Intercom.
3. To end the intercom call, press OFF
or place the handset back in the
telephone base or charger.
NOTES
The destination handset rings and its
•
To cancel the intercom call before it is
answered, press OFF or INT.
screen displays HS X is calling.
2. To answer the intercom call on the
• Press OFF or MUTE on the destination
handset to temporarily silence the intercom
ringer.
destination handset, press
or any dialing key (0-9,
,
,
, INT
or
).
The outside call is still on hold and both
handsets now display Intercom. You
can now have a private conversation
with the destination handset.
•
If the destination handset does not answer
the intercom call within 100 seconds, is on
a call or out of range, the originating
handset displays Unable to call and
returns to idle mode.
•
If there is an incoming call while the
originating handset displays Calling HS X,
the intercom request will be stopped and
the screen displays Incoming call.
14
NOTES
Phonebook
• To cancel the intercom call before it is
answered, press OFF, or INT on your
handset.
The phonebook can store up to
50 entries, which are shared by all
handsets. Each entry may consist of a
telephone number up to 30 digits, and a
name up to 15 characters.
• If the destination handset does not
answer within 100 seconds, is in use, on
a call or is out of range, the originating
handset displays Unable to call and then
reconnects to the outside call.
Any additions, deletions or edits made
on one handset will be reflected on
other handsets.
3. From this intercom call, you have the
following options:
If the telephone number in the
• You can let the destination handset
join you on the outside call in
a three-way conversation.
Press and hold INT on the
originating handset.
phonebook exceeds 15 digits, a dash
appears after the 14th digit and then the
remaining digits are shown beginning
with a dash alternately.
• You can transfer the call. Press
OFF, or place your handset back
in the telephone base or charger.
Your handset displays Line in use.
The destination handset is then
connected to the outside call.
Add a phonebook entry
1. Enter the number when the phone is
not in use. Press SELECT, then go to
Step 4.
-OR-
Press Menu when the handset is not
in use.
• You can press INT to switch
between the outside call (Outside
call displays) and the intercom call
(Intercom displays).
2. Press or to choose Phonebook,
and then press SELECT.
3. Press SELECT to choose Add new
• The destination handset can end
the intercom call by pressing OFF,
or by placing the handset back in
the telephone base or charger.
The outside call continues with the
original system handset.
entry.
4. When Enter number displays, use
the dialing keys to enter a number
(up to 30 digits).
-OR-
Copy a number from the redial list
by pressing REDIAL. Then press
,
, or REDIAL repeatedly to find the
desired number. Press SELECT to
copy the number.
5. Press SELECT to move on to the
name.
6. When Enter name displays, use the
dialing keys to enter a name (up to 15
characters). Additional key presses
show other characters on that key.
The first character of every word is
capitalized.
15
7. Press SELECT to save. You hear
a confirmation tone and then the
handset returns to the previous
menu.
Alphabetical search
1. Follow the steps in Review the
phonebook entries to enter the
phonebook.
While entering names and numbers,
you can:
2. Use the dialing keys to enter the
letter associated with the name.
For example, if you have entries for
Jenny, Jessie, Kristen and Laura in
your phonebook, press 5 (JKL) once
to see Jenny (when Jenny displays,
press to see Jessie), twice to see
Kristen, or three times to see Laura.
If there is no name entry matching
your search, the next closest match
in alphabetical order appears. If
• Press or to move the cursor to
the left or right.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all
digits.
• Press and hold PAUSE to enter a
dialing pause (a p appears).
• Press 0 to add a space.
necessary, press or to browse.
Review the phonebook entries
Entries are sorted alphabetically.
Edit a phonebook entry
1. Search for the desired entry in
the phonebook (see Review the
phonebook entries or
1. Press
when the phone is not in
use. The handset displays the first
entry in the phonebook.
Alphabetical search).
2. Press or to browse through the
phonebook, or use the dialing keys to
start a name search.
2. When the desired entry displays,
press SELECT.
3. Use the dialing keys to edit the
-OR-
number, and then press SELECT.
1. Press MENU when the phone is not
4. Use the dialing keys to edit the name,
and then press SELECT to save. You
hear a confirmation tone.
in use.
2. Press or to choose Phonebook,
and then press SELECT.
3. Press or to choose Review, and
then press SELECT.
4. The handset displays the first
phonebook entry. Press or to
browse through the phonebook.
NOTES
•
•
If the telephone number in the phonebook
exceeds 15 digits, - appears in front of
the telephone number and shows the
remaining numbers alternately.
You hear a double beep when you reach
the beginning or end of the phonebook.
16
Delete a phonebook entry
Caller ID
If you subscribe to caller ID service,
information about each caller appears
after the first or second ring. If
you answer a call before the caller
information appears on the screen, it
will not be saved in the caller ID log.
1. Search for the desired entry in
the phonebook (see Review the
phonebook entries or
Alphabetical search).
2. When the desired entry appears,
press DELETE. The screen displays
Delete entry?.
The caller ID log stores up to 30 entries.
Each entry has up to 24 digits for the phone
number and 15 characters for the name.
3. Press SELECT to confirm. The
screen displays Deleting .... Then
you hear a confirmation tone.
If the telephone number has more that
15 digits, only the last 15 digits appear.
If the name has more than 15 characters,
only the first 15 characters are shown
and saved in the caller ID log.
Dial a phonebook entry
1. Search for the desired entry in
the phonebook (see Review the
phonebook entries or Alphabetical
search).
Entries appear in reverse chronological
order. When the caller ID log is full, the
oldest entry is deleted to make room for
new incoming call information.
2. Press
or to dial.
Caller ID log entries are shared by all
system handsets (for multiple handset
models only). Any deletions made on
one handset are reflected on all other
handsets.
NOTE
•
This product can provide information
only if both you and the caller are in
areas offering caller ID service and if
both telephone service providers use
compatible equipment. The time and
date are sent by your telephone service
provider along with the call information.
Review the caller ID log
Review the caller ID log to find out who
called, to return the call, or to copy the
caller’s name and number into your
phonebook.
1. Press CID when the phone is not in
use. The handset displays the first
entry in the caller ID log.
2. Press or to browse.
17
-OR-
If you do not want to review the missed
calls one by one, press and hold
CANCEL on the handset when not in
use to clear the missed call indicator. All
the entries are then considered old. You
hear a confirmation tone.
1. Press MENU when the phone is not
in use.
2. Press or to scroll to Caller ID
log, and then press SELECT twice
to choose Review. The handset
displays the first entry in the caller ID
log.
View dialing options
Although the caller ID log entries
received have 10 digits (the area code
plus the seven-digit number), in some
areas, you may dial only the seven
digits, or a 1 plus the seven digits, or
a 1 plus the area code plus the seven
digits. You can change the number of
digits that you dial from or store to the
phonebook.
3. Press or to browse.
NOTE
•
You hear a double beep when you reach
the beginning or end of the caller ID log.
Memory match
If the incoming telephone number
matches the last seven digits of a
telephone number in your directory,
the name that appears on the screen
matches the corresponding name in
your phonebook.
While reviewing the caller ID log, press
(pound key) repeatedly to display
different dialing options for local and
long distance numbers before dialing or
saving the telephone number in the
phonebook.
For example, if Linda Jones Smith calls,
his name appears as Linda if this is
how you entered it into your phonebook.
Press 1 repeatedly if you need to add
or remove 1 in front of the telephone
number before dialing or saving it in
the phonebook.
NOTE
•
The number shown in the caller ID log
is in the format sent by the telephone
service provider. It usually delivers
10-digit phone numbers (area code plus
telephone number). If the last seven digits
of the incoming telephone number do not
match a number in your phonebook, the
name appears as it is delivered by the
telephone service provider.
Mike Smith
800-595-9511
ECO
10:15PM
12/25
Press # 1-800-595-9511
Missed call indicator
When there are calls that have not
been reviewed in the caller ID log, the
handsets display XX missed calls.
Press #
Press #
Press #
-OR-
595-9511
1-595-9511
800-595-9511
Each time you review a caller ID log
entry marked NEW, the number of
missed calls decreases by one.
Press 1 1-800-595-9511
800-595-9511
Press 1
When you have reviewed all the
missed calls, the missed call indicator
no longer displays.
18
NOTE
NOTE
•
If you have programmed the home area
code, only the last seven digits of the
incoming phone numbers from that area
code will be displayed while reviewing the
•
If you save an entry which already exists
in the phonebook, the handset displays
Number repeated and then returns to
previous screen.
caller ID log. Press
repeatedly to
display all possible dialing options.
Delete the caller ID log entries
1. Search for the desired caller ID log
Dial a caller ID log entry
entry (see Review the Caller ID log).
1. Search for the desired caller ID log
2. Press DELETE to delete the
displayed entry. The screen displays
Deleting.... Then you hear a
confirmation tone.
entry (see Review the Caller ID log).
2. When the desired entry displays,
press
or to dial.
Save a caller ID log entry to the
phonebook
1. Search for the desired caller ID log
To delete all entries:
1. Press MENU when the phone is not
in use.
entry (see Review the Caller ID log).
2. Press or to scroll to Caller ID
log, and then press SELECT.
2. When the desired entry displays,
press SELECT.
3. Press or to scroll to Delete all,
and then press SELECT.
3. Press SELECT to choose
To Phonebook. Then the handset
displays Enter number.
4. When the screen shows Delete all?.
Press SELECT to confirm. The
screen displays Deleting... and then
you hear a confirmation tone. The
screen returns to the previous menu.
4. Use the dialing keys to edit the
number, if necessary. Press SELECT
to move to the name. The handset
displays Enter name.
5. Use the dialing keys to add or edit the
name.
6. Press SELECT when done.
While entering names and numbers,
you can:
• Press or to move the cursor to
the left or right.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all
digits.
• Press and hold PAUSE to enter a
dialing pause (a p appears).
• Press 0 to add a space.
19
-OR-
Call block
Copy a number from the redial list
by pressing REDIAL. Then press
, or REDIAL repeatedly to find the
desired number. Press SELECT to
copy the number.
If you have subscribed to caller ID
service, you can set the telephone
to block unknown calls and certain
undesired calls. The call block list can
store up to 20 entries.
,
6. Press SELECT to move on to the
When a call is blocked, the caller will
hear a simulated busy tone for one ring
cycle. The call recipient may pick up the
call during the first ring when there is no
caller ID information. Otherwise, the call
is disconnected.
name.
7. When Enter name displays, use the
dialing keys to enter a name (up to
15 characters). Additional key
presses show other characters on
that key. The first character of every
word is capitalized.
Block unknown calls
All incoming calls with unknown
numbers will be blocked.
8. Press SELECT to save. You hear
a confirmation tone and then the
handset returns to the previous
menu.
1. Press MENU when the handset is not
While entering names and numbers,
you can:
in use.
2. Press
or to choose Call block,
• Press or to move the cursor to
the left or right.
• Press DELETE to erase a digit.
then press SELECT.
3. Press
or to choose Calls w/o
num, then press SELECT.
• Press and hold DELETE to erase all
4. Press or to choose Unblock or
Block, then press SELECT. You hear
a confirmation tone.
digits.
• Press and hold PAUSE to enter a
dialing pause (a p appears).
• Press 0 to add a space.
Add a call block entry
1. Press MENU when the phone is not
Review call block list
1. Press MENU when the phone is not
in use.
2. Press or to choose Call block,
in use.
and then press SELECT.
2. Press or to choose Call block,
3. Press SELECT to choose
and then press SELECT.
Block list.
3. Press or to choose Block list,
4. Press or to choose Add new
and then press SELECT.
entry, and then press SELECT.
4. Press or to choose Review, and
5. When Enter number displays, use
the dialing keys to enter a number (up
to 30 digits).
then press SELECT.
5. Press or to browse through the
directory.
NOTE
•
The handset displays List empty if there
are no block entries.
20
Edit a call block list entry
1. Search for the desired call block entry
Sound settings
Key tone
(see Review call block list).
You can turn the key tone on or off for
each handset. If you turn the key tone
off, there are no beeps when you press
the handset keys.
2. When the desired entry displays,
press SELECT. The handset displays
Enter number.
3. Use the dialing keys to edit the
number.
1. Press MENU when the handset is not
in use.
4. Press SELECT. The handset displays
Enter name.
2. Press or to choose Settings,
and then press SELECT.
5. Use the dialing keys to edit the name.
3. Press or to choose Key tone,
6. Press SELECT to save.
and then press SELECT.
4. Press or to choose On or Off.
Save a caller ID log entry to call
block list
1. Search for the desired caller ID log
entry (see Review the Caller ID log).
2. When the desired entry displays,
5. Press SELECT to save your
selection. Then the handset returns
to the previous menu. You hear a
confirmation tone.
press SELECT.
3. Press or to scroll to To Call
Ringer tone
You can choose from different ringer
tones for each handset.
block, then press SELECT.
4. The handset displays Enter Number.
Use the dialing keys to edit the
number, when necessary. Press
SELECT to move to the name. The
handset displays Enter name.
1. Press MENU when the handset is not
in use.
2. Press or to choose Ringers, and
then press SELECT.
5. Use the dialing keys to add or edit the
name.
3. Press or to choose Ringer tone,
and then press SELECT.
6. Press SELECT when done. You hear
4. Press or to sample each ringer
tone.
a confirmation tone.
5. Press SELECT to save your
selection. Then the handset returns
to the previous menu. You hear a
confirmation tone.
Delete a call block list entry
1. Search for the desired call block entry
(see Review the call block list).
2. Press DELETE. You hear a
confirmation tone and the handset
displays the next entry.
NOTE
•
If you turn off the ringer volume, you will
not hear ringer tone samples.
NOTE
•
If the call block list is empty after an entry
is deleted, the handset displays List
empty. You hear a confirmation tone.
21
Ringer volume
Quiet mode
You can set the ringer volume or turn
the ringer off on each handset. When
You can turn on the quiet mode for a
period of time (1-12 hours). During this
period, all tones (except paging tone)
are muted.
the ringer is off,
screen.
appears on the
1. Press MENU when the handset is not To set the duration and turn on the
in use. quiet mode:
2. Press or to choose Ringers, and 1. Press and hold
when the
then press SELECT.
handset is not in use.
3. Press or to select Ringer
2. The handset displays Quiet: _ _
hours. Use the dialing keys (0-9) to
enter the desired duration (1-12).
volume, and then press SELECT.
4. Press or to sample each volume
level.
3. Press SELECT to save. You hear
5. Press SELECT to save your
selection. Then the handset returns
to the previous menu. You hear a
confirmation tone.
a confirmation tone. The handset
displays Quiet mode on and
.
To turn off the quiet mode:
• Press and hold
when the
NOTE
handset is not in use. The handset
displays Quiet mode off briefly and
then returns to idle.
•
If the ringer volume is set to off, that
handset is silenced for all incoming calls
except paging tone.
NOTE
Temporary ringer silencing
•
When you change the settings of the
ringer tone or ringer volume, you can still
hear the samples even if the quiet mode
is on.
When the telephone is ringing, you can
temporarily silence the ringer of the
handset and telephone base without
disconnecting the call. The next call
rings normally at the preset volume.
• Press OFF or MUTE on the handset
and it displays Ringer muted and
.
NOTES
•
Each handset and the base ring when
there is an incoming call unless the ringer
volume of that device is turned off.
22
Turn off the new voicemail
indicators
Retrieve voicemail from
telephone service
If you have retrieved your voicemail
while away from home, and the
handset still displays the new voicemail
indicators, use this feature to turn off the
indicators.
Voicemail is a feature available from
most telephone service providers. It
may be included with your telephone
service, or may be optional. Fees may
apply.
NOTE
Retrieve voicemail
• This feature turns off the indicators only, it
does not delete your voicemail messages.
When you received a voicemail, the
handset displays New voicemail
1. Press MENU when the handset is not
in use.
and
.
2. Press or to choose Settings,
To retrieve, you typically dial an access
number provided by your telephone
service provider, and then enter a
security code. Contact your telephone
service provider for instructions on how
to configure the voicemail settings and
listen to messages.
and then press SELECT.
3. Press or to choose Clr
voicemail, and then press SELECT.
You hear a confirmation tone.
NOTE
• After you have listened to all new
voicemail messages, the indicators on the
handset turn off automatically.
Set your voicemail number
You can save your access number on
each handset for easy access to your
voicemail. After you saved the voicemail
number, you can press and hold
retrieve voicemail.
to
1. Press MENU when the handset is not
in use.
2. Press or to choose Settings,
and then press SELECT.
3. Press or to choose Voicemail #,
and then press SELECT.
4. Use the dialing keys to enter the
voicemail number (up to 30 digits).
5. Press SELECT to save. You hear a
confirmation tone.
23
Expand your telephone
system
You can add new handsets (CS6909),
cordless headsets (IS6100) or
speakerphones (MA3222 or AT&T
TL80133) to your telephone system. All
accessories are sold separately. Your
telephone base supports a maximum of
five devices.
Screen messages
You are calling
another handset (for
intercom calls).
Calling HS X
(for models with two
or more
handsets only)
You have just ended
a call.
Ended
Another handset is
calling (for intercom
calls).
HS X is
calling
(for models with two
or more handsets
only)
For more details, refer to the user’s
manual that comes with your new
device.
There is an incoming
call.
Incoming
call
Two handsets are
required for an
intercom call.
INT needs 2
HS
The handset is on an
intercom call.
Intercom
You have started the
intercom process or
started transferring a
call, and need to enter
the desired handset
number.
Intercom to
(for models with
three or more
handsets only)
A system handset or
another telephone on
the same line is
in use.
Line in use
There are no
phonebook entries.
List empty
The battery needs to
be recharged.
Low battery
MUTE is turned off
and the person on the
other end can hear
you.
Microphone
on
You have turned
off the handset
Muted
microphone. The
other party cannot
hear you but you can
hear the other party.
24
There are new
The handset
registration is in
progress.
New
Registering...
Ringer muted
voicemail message(s)
from your telephone
service provider.
voicemail
The handset ringer
is muted temporarily
during an incoming
call.
You place the handset
in the telephone base
or charger without
installing a battery
in it.
No battery
The handset
speakerphone is in
use.
Speaker
There is no telephone
line connected.
No line
Screen display on
a non-registered
handset.
To register
HS...
Another handset
is already in the
phonebook or caller
ID log.
Not
available
...see manual
The handset is out of
range while on a call.
Unable to
call
The telephone
number you have
entered is already
stored in the
Number
repeated
Failed phone call (the
telephone line is in
use).
phonebook.
Failed intercom call
(there are already two
handsets being used).
The telephone base
has lost power, or
the handset is out of
range.
Out of range
or no pwr at
base
There are new calls in
the caller ID log.
XX missed
calls
The handset is on a
call.
Phone
All system handsets
are being paged.
** Paging **
The battery is very
low. Put the handset
in the telephone
base or charger for
recharging.
Put in
charger
The quiet mode is
turned off.
Quiet mode
off
The quiet mode is
turned on.
Quiet mode
on
The phonebook is full.
You cannot save any
new entry unless you
delete some current
entries.
Rec mem full
Reg. failed
The handset
registration is not
successful.
25
I cannot dial
out.
Make sure there is a dial
tone before dialing. It
is normal if the handset
takes a second or two
to synchronize with the
telephone base before
producing a dial tone.
Wait an extra second
before dialing.
Frequently asked
questions
Below are the questions most frequently
asked about the cordless telephone.
If you cannot find the answer to your
question, visit our website at
www.vtechphones.com or call
Eliminate any
background noise.
Mute the handset
before dialing, or dial
from another room in
your home with less
background noise.
1 (800) 595-9511 for customer service.
My telephone
does not work
at all.
Make sure the telephone
base is installed
properly, and battery is
installed and charged
correctly. For optimum
daily performance,
return the handset to
the telephone base after
use.
The display
shows To
The handset is
deregistered from the
telephone base.
register HS...
and ...see
1. Unplug the telephone
base power adapter
from the power outlet,
and then plug it back
in.
2. Place the handset in
the telephone base to
register it back.
The handset shows
Registered and you
hear a beep when the
registration process
completes. This process
takes about 90 seconds
to complete.
manual
alternately. The
handset does
not work at all.
The display
Disconnect the
shows No line. telephone line cord from
I cannot hear
the dial tone.
your telephone and
connect it to another
telephone. If there is
no dial tone on that
other telephone either,
then the telephone line
cord may be defective.
Try installing a new
telephone line cord.
If changing telephone
line cord does not
help, the wall jack (or
the wiring to this wall
jack) may be defective.
Contact your telephone
service provider.
The display
shows Low
battery.
Place the handset in
the telephone base or
charger for charging.
The battery
does not
charge in the
handset or the correctly.
handset battery
does not
accept charge.
Make sure the handset is
placed in the telephone
base or charger
You may be using a new
cable or VoIP service,
the existing telephone
jacks in your home may
no longer work. Contact
your service provider for
solutions.
If the battery is
completely depleted,
charge the battery for at
least 30 minutes before
use.
You may need to
purchase a new battery.
The telephone Make sure the ringer
does not ring
when there is
an incoming
call.
volume is not set to off.
The handset may be too
far from the telephone
base. Move it closer to
the telephone base.
26
My handset
beeps and is
Move the handset closer
to the telephone base. It
There is
The handset may be out
of range. Move it closer
to the telephone base.
interference
during a
not performing may be out of range.
normally.
telephone
conversation.
My calls fade
out when
I am using
the cordless
handset.
If you subscribe to
I hear other
calls when
using the
Disconnect the telephone
base from the telephone
wall jack. Plug in a
high-speed Internet
service (DSL - digital
subscriber line) through
your telephone line, you
must install a DSL filter
between the telephone
line cord and the
telephone.
different telephone. If you
still hear other calls, the
problem is probably in
the wiring or telephone
service. Contact your
telephone service
telephone wall jack. The
filter prevents noise and
caller ID problems caused
by DSL interference.
Contact your DSL
service provider for more
information about DSL
filters.
provider.
I hear noise on Make sure the telephone
the cordless
handset and
the keys do not
work.
line cord is plugged in
securely.
Appliances or other
cordless telephones
plugged into the
same circuit as the
telephone base can
cause interference. Try
moving the appliance
or telephone base to
another outlet.
The location of your
telephone base can
impact the performance
of your cordless phone.
For better reception,
install the telephone base
in a centralized location
within your home or
office, away from walls
or other obstructions.
In many environments,
elevating the telephone
base improves overall
performance.
27
The telephone Caller ID is a subscription
I subscribe to a Make sure your
does not
service. You must
nontraditional
telephone
service that
uses my
computer is powered
receive caller
ID or the
subscribe to this service
from your telephone
on, and your Internet is
working properly.
telephone does service provider for this
not show caller feature to work on your
Make sure to plug your
USB telephone adapter
into a dedicated USB
port on your computer.
Do not plug into a
multiple port USB hub
(USB splitter) that is not
powered.
computer
ID during call
waiting.
telephone.
to establish
connections,
and my
telephone
doesn’t work.
Both your and the
caller’s telephone
service providers
must use equipment
compatible with the
caller ID service.
In a few rare instances,
the USB port on your
computer may not have
enough power. In these
instances, try using a
USB hub with its own
external power supply.
The caller may not be
calling from an area
which supports caller ID.
The caller ID information
displays after the first or
second ring.
If you are using
The display
shows Out of
range or no
pwr at base.
The handset may be out
of range. Move it closer
to the telephone base.
a firewall, it may
prevent access to your
nontraditional telephone
service. Contact your
service provider for more
information.
Make sure the power
cord is securely plugged
into the telephone base.
Use a working electrical
outlet not controlled by a
wall switch.
I accidentally
set my LCD
language to
Spanish or
While the handset is
not in use or is on a
call, press MENU and
then enter 364# to
change the handset
LCD language back to
French, and
I don’t know
how to change English.
it back to
English.
28
ECO mode
General product care
This power conserving technology
reduces power consumption for optimal
battery performance. The ECO mode
activates automatically whenever
the handset is synchronized with the
telephone base.
Taking care of your telephone
Your cordless telephone contains
sophisticated electronic parts, so it must
be treated with care.
Avoid rough treatment
Place the handset down gently. Save
the original packing materials to protect
your telephone if you ever need to ship
it.
The handset shows ECO when the
ECO mode activates.
Avoid water
Your telephone can be damaged if
it gets wet. Do not use the handset
outdoors in the rain, or handle it with wet
hands. Do not install the telephone base
near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause
power surges harmful to electronic
equipment. For your own safety, take
caution when using electrical appliances
during storms.
Cleaning your telephone
Your telephone has a durable plastic
casing that should retain its luster for
many years. Clean it only with a dry non-
abrasive cloth. Do not use dampened
cloth or cleaning solvents of any kind.
29
The RBRC® seal
FCC, ACTA and IC
regulations
The RBRC® seal on the nickel-metal
hydride battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program to
collect and recycle these batteries at the
end of their useful lives, when taken out
of service within the United States and
Canada.
FCC Part 15
This equipment has been tested and
found to comply with the requirements
for a Class B digital device under Part
15 of the Federal Communications
Commission (FCC) rules. These
requirements are intended to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
The RBRC® program provides a
convenient alternative to placing used
nickel-metal hydride batteries into the
trash or municipal waste, which may be
illegal in your area.
VTech’s participation in RBRC® makes it
easy for you to drop off the spent battery
at local retailers participating in the
RBRC® program or at authorized VTech
product service centers. Please call
1 (800) 8 BATTERY® for information on
Ni-MH battery recycling and disposal
bans/restrictions in your area. VTech’s
involvement in this program is part of its
commitment to protecting our environment
and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY®
are registered trademarks of
Rechargeable Battery Recycling
Corporation.
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Changes or modifications to this
equipment not expressly approved by
the party responsible for compliance
could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference,
30
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation. Privacy of communications
may not be ensured when using this
telephone.
connecting to a single line and an RJ14
jack for two lines. See the installation
instructions in the user’s manual.
The Ringer Equivalence Number (REN)
is used to determine how many devices
you may connect to your telephone
line and still have them ring when you
are called. The REN for this product is
encoded as the 6th and 7th characters
following the US: in the product identifier
(e.g., if ## is 03, the REN is 0.3). In most,
but not all areas, the sum of all RENs
should be five (5.0) or less. For more
information, contact your telephone
service provider.
This equipment may not be used with
Party Lines. If you have specially wired
alarm dialing equipment connected
to your telephone line, ensure the
connection of this equipment does not
disable your alarm equipment. If you
have questions about what will disable
alarm equipment, consult your telephone
service provider or a qualified installer.
To ensure safety of users, the FCC
has established criteria for the amount
of radio frequency energy that can be
safely absorbed by a user or bystander
according to the intended usage of the
product. This product has been tested
and found to comply with the FCC
criteria. The handset may be safely
held against the ear of the user. The
telephone base shall be installed and
used such that parts of the user’s body
other than the hands are maintained at
a distance of approximately 20 cm
(8 inches) or more.
This Class B digital apparatus complies
with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
If this equipment is malfunctioning, it
must be unplugged from the modular jack
until the problem has been corrected.
Repairs to this telephone equipment can
only be made by the manufacturer or its
authorized agents. For repair procedures,
follow the instructions outlined under the
Limited warranty.
FCC Part 68 and ACTA
This equipment complies with
Part 68 of the FCC rules and with
technical requirements adopted by the
Administrative Council for Terminal
Attachments (ACTA). The label on
the back or bottom of this equipment
contains, among other things, a
product identifier in the format US:
AAAEQ##TXXXX. This identifier must
be provided to your telephone service
provider upon request.
If this equipment is causing harm to
the telephone network, the telephone
service provider may temporarily
discontinue your telephone service. The
telephone service provider is required
to notify you before interrupting service.
If advance notice is not practical, you
will be notified as soon as possible. You
will be given the opportunity to correct
the problem and the telephone service
provider is required to inform you of
your right to file a complaint with the
FCC. Your telephone service provider
may make changes in its facilities,
equipment, operation, or procedures
that could affect the proper functioning
The plug and jack used to connect this
equipment to premises wiring and the
telephone network must comply with
applicable Part 68 rules and technical
requirements adopted by ACTA. A
compliant telephone cord and modular
plug is provided with this product. It is
designed to be connected to a compatible
modular jack that is also compliant. An
RJ11 jack should normally be used for
31
of this product. The telephone service
provider is required to notify you if such
changes are planned.
If this product is equipped with a corded
or cordless handset, it is hearing aid
compatible.
California Energy
Commission battery
charging testing
instructions
This telephone meets the California Energy
Commission (CEC) regulations for energy
consumption. It is not necessary to activate
the energy conserving mode during normal
usage, unless you want to charge the battery
only and disable all telephone functions.
If this product has memory dialing
locations, you may choose to store
emergency telephone numbers (e.g.,
police, fire, medical) in these locations.
If you do store or test emergency
numbers, please:
Remain on the line and briefly explain
the reason for the call before hanging up.
Perform such activities in off-peak hours,
such as early morning or late evening.
To activate the CEC battery charging
testing mode:
1.Unplug the telephone base power
adapter from the power outlet. Make sure
all handsets are plugged with charged
batteries before proceeding.
Industry Canada
2.While you press and hold
This device complies with Industry
Canada license-exempt RSS
standard(s).
Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that
may cause undesired operation.
/FIND HANDSET, plug the telephone base
power adapter back to the power outlet.
3.After about 20 seconds, when the
IN USE light starts flashing, release
/FIND HANDSET and then press it again
within 2 seconds.
The process takes up to one minute to
complete. When the phone successfully
enters the CEC battery charging testing
mode, the IN USE light turns off and all
handsets display To register HS... and
...see manual alternately.
Privacy of communications may not be
ensured when using this phone.
When the phone fails to enter this mode,
repeat Step 1 through Step 3 above. The
telephone base will be powered up as
normal if you fail to press /FIND HANDSET
within 2 seconds in Step 3.
The term ‘’IC:‘’ before the certification/
registration number only signifies
that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN)
for this terminal equipment is 0.1. The
REN is an indication of the maximum
number of devices allowed to be connected
to a telephone interface. The termination
on an interface may consist of any
combination of devices subject only to
the requirement that the sum of the RENs
of all the devices does not exceed five.
This product meets the applicable
Industry Canada technical
specifications.
To deactivate the CEC battery charging
testing mode:
1.Unplug the telephone base power adapter
from the power outlet, and then plug
it back in. Then the telephone base is
powered up as normal.
2.Place the handset in the telephone base
to register it back. The handset displays
Registering....
NOTE
•
The handset shows Registered and you
hear a beep when the registration process
completes. The registration process takes
about 90 seconds to complete.
32
similaires. Ne placez pas cet appareil
proximité d’un élément de chauffage
ni d’une plinthe électrique. De plus,
ne l’installez pas dans une unité
murale ou un cabinet fermé qui ne
possède pas d’aération adéquate.
8. Ne faites fonctionner cet appareil
qu’avec le type d’alimentation indiqué
sur les étiquettes de l’appareil. Si
vous ne connaissez pas le voltage
de votre maison, consultez votre
marchand ou votre fournisseur
d’électricité.
9. Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil
dans un endroit sécuritaire, lè oè
personne ne pourra trébucher sur
la ligne d’alimentation ni le cordon
téléphonique modulaire.
For C-UL compliance only
Mesures de sécurité
importantes
Afin de réduire les risques d’incendie,
de blessures corporelles ou
d’électrocution, suivez toujours ces
mesures préventives de base lorsque
vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions
et mises en garde inscrites sur
l’appareil.
3. Débranchez ce téléphone de la prise
murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en
aérosol. N’utilisez qu’un chiffon doux
et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau,
tel que près d’un bain, d’un lavabo,
d’un évier de cuisine, d’un bac de
lavage ou d’une piscine, ou dans un
sous-sol humide ou sous la douche.
5. Ne déposez pas ce téléphone sur un
chariot, support ou table chancelants.
L’appareil pourrait tomber et ètre
sérieusement endommagé.
10.N’insérez jamais d’objets è travers
les fentes et ouvertures de cet
appareil, car ils pourraient toucher
è des points de tension dangereux
ou court-circuiter des pièces, ce qui
constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de
liquides dans l’appareil.
11.Afin de réduire les risques
d’électrocution, ne démontez pas
l’appareil, mais apportez-le plutôt è
un centre de service qualifié s’il doit
ètre réparé. En enlevant le couvercle,
vous vous exposez è des tensions
dangereuses ou autres dangers
similaires. Un remontage inadéquat
peut ètre è l’origine d’une électrocution
lors d’une utilisation ultérieure de
l’appareil. Débranchez l’appareil
avant de procéder au nettoyage.
Utilisez un chiffon humide et doux.
12.Ne surchargez pas les prises de
courant et les rallonges.
6. Évitez d’installer le système
téléphonique dans les endroits
soumis è une température extrème, è la
lumière directe du soleil ou è proximité
immédiate d’autres appareils
électriques ou électroniques.
Protégez votre téléphone contre les
sources d’humidité, la poussière, les
vapeurs et les liquides corrosifs.
7. Le boîtier de l’appareil est doté de
fentes et d’ouvertures d’aération
situées è l’arrière ou en dessous.
Afin d’empècher la surchauffe, ces
ouvertures ne doivent pas ètre
obstruées en plaçant l’appareil sur
un lit, divan, tapis ou autre surface
13.Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service è la clientèle
33
de VTech dans les cas suivants:
• Lorsque le cordon d’alimentation
est endommagé ou écorché.
• Si du liquide a été échappé dans
l’appareil.
• Si l’appareil a été exposé une
source d’humidité telle que la
pluie ou l’eau.
• Si le produit ne fonctionne pas
• normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les
d’un endroit comportant des
concentrations de gaz inflammables,
moins que la ventilation soit
adéquate. Une flammèche dans
un tel endroit pourrait provoquer
un incendie ou une explosion.
De tels environnements peuvent
comprendre: des endroits oè l’on
utilise de l’oxygène médical sans
ventilation adéquate; des gaz
industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une
fuite de gaz naturel, etc.
commandes indiquées dans le les
instructions de fonctionnement.
Les réglages incorrects des autres
commandes pourraient provoquer
un dommage qui pourrait exiger
un travail exhaustif de la part d’un
technicien autorisé afin de rétablir
le fonctionnement normal de
l’appareil.
16. Ne placez que le combiné de votre
téléphone près de votre oreille
lorsqu’en mode de conversation.
17. Ces adaptateurs ont été conçus pour
ètre orientés en position verticale
ou montés au sol. Les broches ne
sont pas conçues pour maintenir
l’adaptateur en place si celui-ci est
barnché dans une prise au plafond
ou sous une table/ armoire.
• Si le produit a été échappé et que
le socle et/ou le combiné a été
endommagé.
CONSERVEZ CES INSTRUCTIONS
• Si le produit affiche une nette
diminution de sa performance.
14. Évitez d’utiliser un téléphone (autre
qu’un sans fil) pendant un orage. Les
éclairs peuvent ètre è l’origine d’une
électrocution.
Pile
• MISE EN GARDE : N’utilisez que la
pile incluse.
• Ne jetez pas la pile au feu. Vérifiez
les instructions spécifiques de mise
aux rebus aupr
locales.
ès des autorités
15. N’utilisez pas le téléphone pour
rapporter une fuite de gaz è
• N’ouvrez pas et ne mutilez pas la
pile. L’électrolyte qui s’en échapperait
est corrosif et pourrait causer des
brèlures ou des blessures aux yeux
ou è la peau. L’électrolyte est toxique
si avalé.
• Soyez prudents lorsque vous
manipulez les piles afin d’éviter les
courts-circuits provoqués par des
matériaux conducteurs.
• Rechargez la pile incluse avec cet
appareil, selon les instructions et
limites spécifiées dans ce guide
d’utilisation.
proximité de la fuite. En certaines
circonstances, une flammèche
pourrait ètre provoquée lorsque
l’adaptateur est branché è une
prise de courant, ou lorsque le
combiné est déposé sur le socle.
Ceci est un événement commun
associé è la fermeture d’un circuit
électrique. L’utilisateur ne devrait pas
brancher le téléphone è une prise de
courant, et ne devrait pas déposer
le combiné chargé sur le socle, si
le téléphone se trouve è proximité
34
Stimulateurs cardiaques implantés
dans l’organisme
radio ; il y a donc la possibilité que
vos conversations téléphoniques
sans fil soient interceptées par
Les simulateurs cardiaques (s’applique
uniquement aux téléphones numériques
sans fil):
des équipements de réception
radio se trouvant dans la portée du
combiné sans fil. Pour cette raison,
vous ne devez pas percevoir les
communications téléphoniques sans fil
comme étant aussi confidentielles.
L’organisme ‘Wireless Technology
Research, LLC (WTR)’, une firme
de recherche indépendante, a mené
une évaluation pluridisciplinaire des
interférences entre les téléphones
sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme.
Appuyée par l’Administration des
aliments et drogues (FDA) des États-
Unis, la firme WTR recommande aux
médecins:
• Alimentation électrique: Le socle de
ce téléphone sans fil doit ètre branché
è une prise électrique fonctionnelle.
La prise électrique ne doit pas ètre
contrôlée par un interrupteur mural.
Les appels ne pourront pas ètre
effectués du combiné sans fil si le
socle est débranché ou mis hors
tension ou si le courant est coupé.
Avis aux détenteurs de stimulateurs
cardiaques
• Possibilité d’interférences aux
téléviseurs: Certains téléphones
sans fil fonctionnent sur des
• Ils doivent tenir le téléphone sans fil
è une distance d’au moins six pouces
du stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone
sans fil directement sur le stimulateur
cardiaque, tel que dans une poche
de chemise, lorsque celui-ci est en
marche.
• Ils doivent utiliser le téléphone sans
fil en l’appuyant sur l’oreille qui se
trouve dans la direction opposée au
stimulateur cardiaque.
fréquences pouvant causer des
interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou
prévenir de telles interférences, ne
placez pas le socle du téléphone
sans fil près ou sur un téléviseur ou
magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner
le téléphone sans fil du téléviseur
ou du magnétoscope afin de réduire
possiblement les interférences.
L’étude effectuée par l’organisme WRS
n’a pas identifié de risque pour les
détenteurs de simulateurs cardiaques
causés par les gens qui utilisent un
téléphone sans fil è proximité de ceux-ci.
• Piles rechargeables: Manipulez
les piles avec soin afin de ne pas
les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le
conducteur peut surchauffer et
causer des blessures. Respectez la
polarité adéquate entre la pile et le
chargeur.
À propos des téléphones sans fil
• Alimentation électrique: Les mèmes
caractéristiques qui constituent
des avantages pour les téléphones
sans fil affichent également des
restrictions. Les appels téléphoniques
sont transmis entre le combiné sans
fil et le socle par le biais d’ondes
35
• Les bloc-piles rechargeables à
l’hydrure métallique de nickel:
Jetez ces blocs-piles de manière
écologique et sécuritaire. Ne les
incinérez pas et ne les percez pas.
Tel que les autres piles de ce type,
elles pourraient dégager une matière
toxique qui peut causer des blessures
corporelles si elles sont brèlées ou
percées.
Limited Warranty
What does this limited warranty
cover?
The manufacturer of this VTech Product
warrants to the holder of a valid proof of
purchase (“Consumer” or “you”) that the
Product and all accessories provided
in the sales package (“Product”) are
free from defects in material and
workmanship, pursuant to the following
terms and conditions, when installed
and used normally and in accordance
with the Product operating instructions.
This limited warranty extends only to the
Consumer for Products purchased and
used in the United States of America
and Canada.
What will VTech do if the Product is
not free from defects in materials
and workmanship during the
limited warranty period (“Materially
Defective Product”)?
During the limited warranty period,
VTech’s authorized service
representative will repair or replace
at VTech’s option, without charge, a
Materially Defective Product. If we
repair the Product, we may use new or
refurbished replacement parts. If we
choose to replace the Product, we may
replace it with a new or refurbished
Product of the same or similar design.
We will retain defective parts, modules,
or equipment. Repair or replacement of
the Product, at VTech’s option, is your
exclusive remedy. VTech will return the
repaired or replacement Products to
you in working condition. You should
expect the repair or replacement to take
approximately 30 days.
How long is the limited warranty
period?
The limited warranty period for the
Product extends for ONE (1) YEAR from
the date of purchase. If VTech repairs or
replaces a Materially Defective Product
under the terms of this limited warranty,
this limited warranty also applies to
the repaired or replacement Product
36
for a period of either (a) 90 days from
the date the repaired or replacement
Product is shipped to you or (b) the
time remaining on the original one-year
warranty; whichever is longer.
call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or dial
1 (800) 267-7377.
NOTE: Before calling for service, please
review the user’s manual - a check of
the Product’s controls and features may
save you a service call.
What is not covered by this limited
warranty?
Except as provided by applicable law,
you assume the risk of loss or damage
during transit and transportation and
are responsible for delivery or handling
charges incurred in the transport of
the Product(s) to the service location.
VTech will return repaired or replaced
Product under this limited warranty.
Transportation, delivery or handling
charges are prepaid. VTech assumes
no risk for damage or loss of the
Product in transit. If the Product failure
is not covered by this limited warranty,
or proof of purchase does not meet the
terms of this limited warranty, VTech
will notify you and will request that you
authorize the cost of repair prior to any
further repair activity. You must pay for
the cost of repair and return shipping
costs for the repair of Products that are
not covered by this limited warranty.
This limited warranty does not cover:
1. Product that has been subjected
to misuse, accident, shipping or
other physical damage, improper
installation, abnormal operation or
handling, neglect, inundation, fire,
water or other liquid intrusion; or
2. Product that has been damaged due
to repair, alteration or modification
by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the
problem experienced is caused by
signal conditions, network reliability,
or cable or antenna systems; or
4. Product to the extent that the
problem is caused by use with
non-VTech accessories; or
5. Product whose warranty/quality
stickers, product serial number plates
or electronic serial numbers have
been removed, altered or rendered
illegible; or
6. Product purchased, used, serviced,
or shipped for repair from outside the
United States of America or Canada,
or used for commercial or institutional
purposes (including but not limited to
Products used for rental purposes);
or
What must you return with the
Product to get warranty service?
1. Return the entire original package
and contents including the Product to
the VTech service location along with
a description of the malfunction or
difficulty; and
2. Include a “valid proof of purchase”
(sales receipt) identifying the Product
purchased (Product model) and the
date of purchase or receipt; and
3. Provide your name, complete
and correct mailing address, and
telephone number.
7. Product returned without a valid proof
of purchase (see item 2 on the next
page); or
8. Charges for installation or set up,
adjustment of customer controls,
and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the United
States of America, please visit our
37
Other limitations
Technical Specifications
This warranty is the complete and
exclusive agreement between you
and VTech. It supersedes all other
written or oral communications related
to this Product. VTech provides no
other warranties for this Product. The
warranty exclusively describes all of
VTech’s responsibilities regarding the
Product. There are no other express
warranties. No one is authorized to
make modifications to this limited
warranty and you should not rely on any
such modification.
Frequency Crystal controlled PLL
control
synthesizer
Transmit
Handset:
frequency
1921.536-1928.448 MHz
Telephone base:
1921.536-1928.448 MHz
Channels
5
Nominal
effective
range
Maximum power allowed
by FCC and IC. Actual
operating range may vary
according to environment
conditions at the time of
use.
State/Provincial Law Rights: This
warranty gives you specific legal
rights, and you may also have other
rights, which vary from state to state or
province to province.
Power
requirements battery
Handset: 2.4V Ni-MH
Limitations: Implied warranties,
including those of fitness for a particular
purpose and merchantability (an
Telephone base:
unwritten warranty that the Product is
fit for ordinary use) are limited to one
year from the date of purchase. Some
states/provinces do not allow limitations
on how long an implied warranty lasts,
so the above limitation may not apply to
you. In no event shall VTech be liable
for any indirect, special, incidental,
consequential, or similar damages
(including, but not limited to lost profits
or revenue, inability to use the Product
or other associated equipment, the cost
of substitute equipment, and claims by
third parties) resulting from the use of
this Product. Some states/provinces do
not allow the exclusion or limitation of
incidental or consequential damages,
so the above limitation or exclusion may
not apply to you.
6V AC @ 300mA
Charger: 6V AC @
300mA
Memory
Phonebook:
50 memory locations;
up to 30 digits and
15 characters
Caller ID log:
30 memory locations; up
to 24 digits and
15 characters
Please retain your original sales
receipt as proof of purchase.
38
Designed to fit your home.
And your life.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
Copyright © 2015 for VTech Communications, Inc.
All rights reserved. 03/15. CS6919-X_WEBCIB_V1.0
Document order number: 91-008301-010-100
|