®
Installing the Tracer MP581/AH541 or Tracer Summit
BMTX BCU Operator-Display Door Upgrade
Ordering numbers: 4020 1156, S3090-0443-62, 4020 1224, S3090-0483-62
To add an operator display to a Tracer MP581 or
Tracer AH541 controller or a BMTX model building
control unit (BCU), remove the enclosure door, then
install the new door with the operator display. Keep
this document at or near the controller for access to
calibration and cleaning instructions for the
operator display.
7. Secure the operator-display cable to the enclo-
sure with a wire tie.
Setting up the operator display
This section shows how to calibrate the operator-
display touch screen and how to adjust the
brightness and contrast. To set up the operator
display screens and security, see the Tracer MP580/
581 Programmable Controller Programming guide
(CNT-SVP01B-EN), the Tracer AH540/541
Configurable Air-Handler Controller Setup and
Operations guide (CNT-SVX05B-EN), or the Tracer
Summit System Programming guide (BMTX-
SVP01A-EN).
Removing the door
To remove the enclosure door:
1. Open the door to a 90° angle from the enclosure
as shown in Figure 1 on page 2.
2. Lift the door to pull the hinge pegs from the
hinge holes.
CAUTION
Avoid Equipment Damage!
Installing the door
To clean the operator display, use a cloth dampened
with commercial liquid glass cleaner. Spraying water
or cleansers directly on the screen may result in
equipment damage.
To install the enclosure door:
1. Unpack the door and check for missing or dam-
aged parts. Check to make sure that the touch
screen and magnetic latches are installed. Check
for cracks in the plastic.
Calibrating the operator display
To calibrate the operator display:
2. Hold the door at a 90° angle from the enclosure
as shown in Figure 1 on page 2.
1. On the home screen, press the Setup button. The
Setup menu appears.
3. Align the hinge pegs on the door with the hinge
holes on the enclosure.
2. On the Tracer MP581 or Tracer AH541, press
the page down button to view the next screen.
4. Gently lower the door until it rests securely in
the hinge holes.
3. Press the Calibrate Touch Screen button. A cali-
bration screen appears.
5. Verify that the door swings freely on the hinges
and that the magnetic latches hold the door
securely when it is closed.
CAUTION
Avoid Equipment Damage!
Do not allow the operator display to come in contact
with sharp objects.
6. Connect the operator-display cable to the opera-
tor display and the main board (Figure 1 on
page 2).
4. Touch the target using a small, pliable, blunt
object, such as a pencil eraser. Hold until the
beeping stops. A second calibration screen
appears.
Note: The operator-display cable passes beneath
the termination board on enclosures with
factory-installed operator displays.
Trane
A Business of American Standard Companies
© 2005 American Standard Inc All rights reserved.
3270 3395 C
Declaration of CE Conformity for the Tracer MP581 and Tracer
AH541 operator displays
Manufacturer name: Trane
Manufacturer address: 4833 White Bear Parkway
St. Paul MN 55110, USA
The manufacturer hereby declares that the product:
Product name: Tracer MP581 and Tracer AH541 operator displays
Model numbers: 4020 1156
Conforms to the following standards or other normative documents:
Electromagnetic emission: EN50090-2-2:1996
(by Council directive 89/336/EEC) Radiated EN55022:
Conducted EN55022:
1998 Class B limit
1998 Class B limit
Electromagnetic immunity: EN50090-2-2:1996
(by Council directive 89/336/EEC) IEC 1000-4-2:1995
EN61000-4-2
6.0 kV by contact
8.0 kV by air
IEC 1000-4-3:1995
EN61000-4-3:1996
Amendment A1:1998
10.0 V/m
80 .. 1000 MHz
IEC 1000-4-4:1995
EN61000-4-4
2.0 kV ac power lines
1.0 kV signal lines
IEC 1000-4-5:1995
EN61000-4-5
2.0 kV
IEC 1000-4-6:1996
EN61000-4-6
10.0 V
0.15 .. 80 MHz
IEC 1000-4-8:1993
EN61000-4-8
IEC 1000-4-11:1994
When and Where Issued
Electromagnetic Emission: 05/18/2001
Electromagnetic Immunity: 05/18/2001
John Olson
Design/Compliance Engineer
Mark of compliance
European contact
Societe Trane (Epinal, France)
1, rue des Ameriques, B.P. 6
F-88191 Golbey Cedex, France
Phone: (33) 329.31.73.00
Fax: (33) 329.81.24.98
This document validates CE conformity of the Tracer MP581 and Tracer AH541 operator displays.
3
3270 3395 C
Declaration of CE Conformity for the Tracer Summit BMTX BCU
operator display
Manufacturer name: Trane
Manufacturer address: 4833 White Bear Parkway
St. Paul MN 55110, USA
The manufacturer hereby declares that the product:
Product name: Tracer Summit BMTX BCU operator display
Model numbers: BMTX001BAA000, BMTX001BAA001,
BMTX001BAA010, BMTX001BAA011
Conforms to the following standards or other normative documents:
Electromagnetic emission: EN61326-1
(by Council directive 89/336/EEC) Radiated EN55022:
Conducted EN55022:
1998 Class B limit
1998 Class B limit
Electromagnetic immunity: EN61326-1
(by Council directive 89/336/EEC)
EN61000-4-2
4.0 kV by contact
8.0 kV by air
EN61000-4-3:1996
10.0 V/m
Amendment A1:1998
80 .. 1000 MHz
EN61000-4-4
2.0 kV ac power lines
1.0 kV signal lines
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
2.0 kV
0.15 .. 80 MHz
30 A/m
1/2 cycle
When and Where Issued
Electromagnetic Emission: 4/5/2004
Electromagnetic Immunity: 4/19/2004
John Olson
Design/Compliance Engineer
Mark of compliance
European contact
Societe Trane (Epinal, France)
1, rue des Ameriques, B.P. 6
F-88191 Golbey Cedex, France
Phone: (33) 329.31.73.00
Fax: (33) 329.81.24.98
This document validates CE conformity of the Tracer Summit BMTX BCU operator display.
3270 3395 C
4
|