Radio Shack Door 63 1124 User Guide

6YQ"$GNN"9KTGNGUU"&QQT"%JKOG  
63-1124  
OWNER’S MANUAL — Please read before using this equipment.  
Transmitter (two included)  
Receiver  
"+/2146#06"  
#
#
If an icon appears at the end of a paragraph,  
go to the box on that page with the  
corresponding icon for pertinent information.  
Indicator — Lights  
when BELL is  
pressed.  
— Warning  
° — Hint  
± — Note  
Rý  
#
Slide ON/OFF to  
ON so that when  
BELL is pressed  
on one of the  
transmitters, a  
door chime  
sounds.  
. — Caution  
— Important  
BELL — Press  
BELL to hear the  
door chime.  
Thank you for purchasing the RadioShack  
Two Bell Wireless Door Chime. It works as a  
doorbell, a remote pager, or an alert. You  
can add an optional external sensor to have  
a chime that alerts you when someone  
walks into a room. The wireless door  
chime’s three-position channel switch  
prevents other transmitters or radio devices  
from sounding the chime.  
/1706+0)"6*'"  
4'%'+8'4  
10"#"(.#6"574(#%'  
4. Drive a screw through the holders.  
Pull out the wire stand on the back of the  
receiver and set it on a table or other flat  
surface.  
5. The transmitter can be slid in and out of  
the holder. To lock the transmitter in the  
holder, fix it with a size M2.6 screw at  
the bottom of the holder.  
10"#"9#..  
1. Drill one 3/16-inch diameter hole and  
insert one of the supplied anchors.  
+056#..+0)"  
."%#76+10".  
$#66'4+'5"#0&"  
5'.'%6+0)"%*#00'.5  
• Use only fresh batteries of the required size  
and type. Always remove old or weak  
batteries. They can leak chemicals that  
destroy electronic circuits  
2. Drive the supplied M3.5 screw into the  
hole until the screw's head extends  
about 1/8 inch from the wall.  
The wireless door chime requires three AAA  
size batteries in both transmitters and three  
C size batteries in the receiver. For best  
performance and longest life, we  
recommend RadioShack alkaline batteries.  
.
• Do not mix old and new batteries, different  
types of batteries (standard, alkaline, or  
rechargeable), or rechargeable batteries of  
different capacities.  
3. Align the keyhole slot on the bottom of  
the receiver with the screw in the wall,  
then slide it down to secure it.  
/1706+0)"6*'"  
64#05/+66'4  
+0"6*'"64#05/+66'4  
1. Slide the transmitter's battery  
compartment door in the direction of the  
arrow to remove it.  
1. Remove the transmitter from the holder.  
2. Use the holder as a template to mark  
two screw holes on the wall.  
2. Use a small flat-blade screwdriver to  
slide the switch inside the battery  
compartment to the desired channel for  
the transmitter.  
3. Remove the holder from the mounting  
surface and drill two 3/16 inch diameter  
holes. Insert one of the supplied  
anchors into each hole.  
© 2002 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
 

RCA Cassette Player 3 5818 User Guide
RCA Universal Remote RCU800B User Guide
Renesas Switch HD74HC1G66 User Guide
RocketFish Bluetooth Headset RF BTHP02 User Guide
Rosewill Network Card RNX N100 User Guide
Runco Computer Monitor High Definition User Guide
Sanyo Projector XG 705A User Guide
SATO Printer TXPSX4 User Guide
Seagate Computer Drive DB352 User Guide
Seagate Computer Monitor ST31250N ND User Guide