Preh Computer Monitor MC15T5 User Manual

Preh Touch Commander and  
Preh Screen Commander  
User Manual and Technical Data  
MC15T5  
 
i. Model with multimedia base  
LC-Display (15”)  
with touch interface  
or monitor glass  
swinging direction  
loudspeaker  
ON/OFF switch  
Pict. 1: front view  
serial connector RS 232  
(touch controller)  
Pict. 2: rear view  
supply voltage connector  
(main power)  
MSR PS/2 Cable  
VGA connector  
audio cable  
Pict. 3: bottom view  
3
subject to change without prior notice  
05.2004  
 
ii. Model with VESA bracketry for pole or wall mount  
LC-Display (15”) with  
touch surface or  
monitor glass  
MSR PS/2  
VGA connector  
(15 pol.)  
Power Supply  
(jack bush)  
serial connector RS 232  
(Touch Controller)  
Loud speaker  
Audio In  
Menu/Left  
Menu/  
Right  
+ Plus  
On/Off  
- Minus  
Pict. 4: front view  
Bracketry  
Threaded bushings  
(M5)  
Pict. 5: rear view II (bracketry)  
4
subject to change without prior notice  
 
05.2004  
iii. Model number define:  
MC15T5xxM3Myy  
LCD Size  
LCD-Type  
(TFT)  
15”  
15  
T5  
Partner Tech Corp.  
Touch-  
technology  
System  
Resistive(Both GS and CB)  
Only Protective Glass(for CB only)  
Multimedia  
R
G
" "  
A
Wallmount  
MSR  
Speaker  
Color  
TK 1+2+3  
Speaker  
White  
Black  
M3  
M
W
S
Accessories  
VGA-cable  
a
VGA-cable & RS232-cable  
power supply + GM power cord  
Ext. power supply + IEC320 (3P)  
Cleaning-set  
GM power cord  
power supply + UK power cord  
power supply + US power cord  
b
GM  
d
" "  
" "  
UK  
US  
1) Multimedia type, 15” LCD monitor, MC15T5xM3Myy (x=R (Resistive type  
for GS, CB), x=G (glass type for CB only); yy=A-Z, 0-9 or blank for  
marketing purposes)  
2) Wallmount type, 15” LCD monitor, Models MC15T5xAM3Myy (x=R  
(Resistaive type for GS, CB), X=G (for CB only), yy=0-9, A-Z or blank  
for marketing purposes) .  
5
subject to change without prior notice  
05.2004  
 
1. General Points  
The Preh Touch Commander serves as graphical input device which makes the screen of  
the computer react immediately on touching graphical operating characters (symbols,  
keys, printings etc.). In this way the touchscreen allows simple, interactive handling of a  
computer even for the PC-inexperienced user. For example this input media offers the  
possibility of reducing training time and costs for the operating staff via a comfortable  
user's dialogue. With its ergonomic design and its comfort in handling the Preh Touch  
Commander is applicable in the fields of medicine, commerce, gastronomy, fast-food as  
well in the restaurants and hotel business.  
The Preh Touch Commander consists of two logical units, the active matrix color LCD  
(TFT) and the highly sensitive touch sensor. These two units must be considered different  
from each other in regard to their function. This means that the appearance of the picture  
on the LCD (screen) is to be considered independent of the touch drivers. As far as the  
computer is concerned the system is connected with the VGA output (LCD) as well as with  
a serial interface (touching function).  
The Touch Commander can thus take over the function of monitor and mouse. A  
standard mouse can be used along with the Touch Commander. Both a standard  
mouse and the Touch Censor will control the position of the cursor on the screen.  
The Preh Screen Commander is without a touch surface. Instead of a touch sensor, you  
will have an anti-reflective, protective glass. In this case you do not have a touch function  
on the screen. You will have a high quality TFT monitor.  
The active matrix Color LCD (TFT) has a diagonal of 15" (381 mm) with a resolution of  
1024x768 pixels as well as 262,144 colors. The display has an especially high degree of  
brightness (typ.250 cd/m²) and color brilliancy. The LCD parameters as for example  
brightness, contrast, picture position etc. are adjustable via the On Screen Display (OSD).  
The analog resistive 5 wire touch technology has a resolution of 1,024x1,024 points.  
Inputting data is done by touching it e.g. with a finger. The activation force necessary to  
register a touch is 1N. The touch surface consists of a hardened polyester foil with a high  
resistance against scratches and an insensitivity to dirt, oil and water splashes. The  
durability of the touch sensor is 35 million single actuation per touching point.  
Multimedia models allow the possibility of giving the user audio feedback via sounds and  
tones. The volume can be adjusted by a rotary control on the rear side of the base.  
6
subject to change without prior notice  
05.2004  
 
The Preh Touch / Screen Commander can also be used with optional VESA bracketry for  
wall mount hardware.  
Pict. 6: Example for adjustable  
Wall mount solution  
2. Contents of packing  
Prior to operating your Preh Touch / Screen Commander, please check whether the  
following parts are included and are in undamaged condition:  
1 Preh Touch Commander or Preh Screen Commander  
1 CD-Rom with touch driver for the operating systems DOS, Windows 3,1x/9x/NT/2000  
XP and OS/2.  
1 Operator's Manual  
1 VGA cable  
1 serial cable (not included with Screen Commander)  
1 power cable  
1 audio cable (only included with multimedia version)  
1 power adapter LEIN CHANG model:LCA01F or CHI SAM model:CH-1024(only included  
with wall mount version)  
7
subject to change without prior notice  
05.2004  
 
3. Installation of Touchscreen  
Please read the following instructions prior to starting to use the Preh Touch / Screen  
Commander!  
The following steps are necessary for a correct function of the device:  
1 Adjust your computer for the proper video resolution [1024x768 / 60 Hz] and switch it  
off, connect Touch / Screen Commander, switch on computer and Touch / Screen  
Commander (see chapter 3.2). If you are asked for confirming the new hardware  
"standard monitor", confirm according to display instructions.  
2 Adjust the video display on the Touch Commander/Screen Commander for graphic  
card in the computer by means of menu point "AUTO TUNING" of the OSD. This step  
is important for the best quality of representation (see chapters 3.3).  
3 Only Touch Commander:  
Installation of touchscreen driver for the corresponding operating system (see chapter  
4).  
The Touch Commander / Screen Commander with VESA mount bracket must be operated  
with the supplied original power supply.  
3.1 Operating Conditions for the System  
The Preh Touch Commander / Screen Commander has been developed for the use with  
PC graphic adapters in SVGA-setting with 1024x768 pixels of resolution. As an operating  
system it is necessary to have either a DOS version 3.3 (or higher), Windows 3.1x,  
Windows 9x, Windows NT, Windows 2000 Windows XP or OS/2.  
For multimedia models a sound card with "Line Out" outputs for generating sounds is  
necessary in addition.  
3.2 Cable Installation and System Settings  
The installation of the cables must be done with the computer switched off. Set the  
correct screen resolution first. The optimum resolution is 1024x768 pixels and the refresh  
rate 60 Hz.  
To begin connect the VGA cable and the RS232 cable as well as the audio cable (see  
pict. 3). Then plug in the AC power cable to the socket (see pict. 3).  
If you now switch on the computer, the LED lights up green after about 3 seconds and the  
corresponding picture appears on the screen. If the computer is in suspend or standby  
mode the LED is red. If the SVGA cable between Touch / Screen Commander and  
computer is disconnected, or that the computer power is switched off, the LED lights up  
red.  
8
subject to change without prior notice  
05.2004  
 
3.3 On Screen Display (OSD)  
For setting the LC Display you find 5 buttons on the front of the housing (see pict. 10).  
2
3
6
5
4
1
Pict. 7: Description of the buttons for perating the On Screen Display.  
1. Power Switch  
Pressing this button turns the display system power on or off.  
When the power switch are switch on, this LED lights in green.  
The LED indicates the different power status with altered LED colors when monitor  
operates in different modes  
2. Power LED  
This LED indicates different states when this unit operates in different modes.  
3. + Plus  
This button is used to adjust the increasing value of the selected OSD control option.  
4. - Minus  
This button is used to adjust the decreasing value of the selected OSD control option.  
5. Menu/Select Right  
Pressing this button pops up the OSD menus on the screen, and used to select ("Down"  
direction) the OSD control options on the screen.  
6. Menu/Select Left  
Pressing this button pops up the OSD menus on the screen, and used to select ("Up"  
direction) the OSD control options on the screen.  
9
subject to change without prior notice  
05.2004  
 
3.3.1 OSD Control  
The LCD monitor can easily adjust the features of displayed image and the buttons in the  
front of the LCD monitor can do the adjustments. When using these controls, OSD menu  
will display the changed on the screen.  
OSD MENU  
- AUTOTUNE  
Press menu/Left or menu/Right call menu then press „+“ to make LCD monitor adjust the  
related parameters automatically for optional display status.  
Important note to menu point AUTO TUNING  
Most video cards differ in regard to their video signals output. For this reason, the MC15  
series monitor may need to be readjusted after connecting it to a computer. The factory  
setting of the monitor is set to produce the best results with a variety of industry standard  
video cards.  
To get the best picture quality, under Windows it would be best to use the Shutdown screen  
when activating the AUTOTUNE menu option. By doing this, the display tries to find the  
display mode.  
The PHASE option may also be used to manually fine tune the picture clarity after  
AUTOTUNE has been done.  
In some cases when using a notebook computer, it might be necessary to deactivate the  
internal display of the notebook on order to obtain a good picture quality.  
- BRIGHTNESS  
Adjust the brightness using + and - button.  
Brightness  
+ 50  
-
10  
subject to change without prior notice  
05.2004  
 
- CONTRAST  
Adjust the contrast using + and - button.  
Contrast  
+ 50  
-
- CLOCK  
Adjust the clock using + and - button.  
Clock  
+ 50  
-
- PHASE  
Adjust the phase using + and - button.  
Phase  
+ 50  
-
- H-POSITION (HORIZONTAL POSITION)  
Pressing + moves the display image to the right; Pressing - moves the display image to the  
left.  
H-Position  
+ 50  
-
- V-POSTION (VERTICAL POSITION)  
Pressing + moves the display image to the upware; Pressing - moves the display image to  
the downware.  
V-Position  
+ 50  
-
- OSD H-POSITION (OSD HORIZONTAL POSITION)  
Pressing + moves the OSD image to the right; Pressing - moves the OSD image to the  
left.  
OSD H-Position  
+ 50  
-
11  
subject to change without prior notice  
05.2004  
 
- OSD V-POSITION (OSD VERTICAL POSITION)  
Pressing + moves the OSD image to the upware; Pressing - moves the OSD image to the  
downware.  
OSD V-Position  
+ 50  
-
- VOLUME  
Adjust the volume using + and - button.  
Volume  
+ 50  
-
- RED COLOR  
Adjust the values of red color gain using + and - button.  
Red Color  
+ 50  
-
- GREEN COLOR  
Adjust the values of green color gain using + and - button.  
Green Color  
+ 50  
-
- BLUE COLOR  
Adjust the values of blue color gain using + and - button.  
Blue Color  
+ 50  
-
- EXIT AND SAVE  
Pressing the + button to save changed value and exit.  
Exit And Save  
+ Yes  
- No  
12  
subject to change without prior notice  
05.2004  
 
- FACTORY RESET  
Press the + button to restore Volume, OSD V-Position, OSD H-Position, V-Position, H-  
Position, Phase, Brightness, Clock to factory default.  
Factory Reset  
+ Yes  
- No  
3.4 Mechanical Adjustment of the LCD Position  
The LCD position on a VESA Mount Preh Touch / Screen Commander cannot be changed  
directly at the Product. The adjustment (tilting or swinging) of the Touch Screen  
Commander depends on the pole or wall mount hardware used.  
The LCD of the Preh Touch / Screen Commander is swingable and tillable. According to  
the usage the LCD position can be changed.  
The below picture shows the model with the multimedia base.  
Pict. 8: adjusting screws on rear side  
The infinitely variable adjustment of the tilting force can be made with two adjusting screws  
located on the rear of the monitor. The adjustment torque (1 - 8 Nm) should be about the  
same on both screws.  
Pict. 9: adjusting screws below  
The infinitely variable adjustment of the swinging force can be made with two adjusting  
screws in the base of the monitor. The adjustment torque (1 - 8 Nm) should be about the  
same on both screws.  
13  
subject to change without prior notice  
05.2004  
 
Note: On changing the housing position you should be careful to not get your fingers too  
near to the opening on the rear side of the housing as they might get pinched there.  
4. Driver Installation  
Important Note:  
A new calibration is always necessary if another touchscreen was connected to the  
computer or if the screen resolution was changed. This means that the calibration between  
touchscreen and computer is adjusted to the mechanical features of the particular  
touchscreen which was connected to the computer at that time.  
A serial Touch Controller is integrated into the Touch Commander. The default setting is  
9600 Bps. Normally this is clearly recognized by the setup programs. If, however, it is not  
clearly recognized, the adjustment can be done manually or by restarting the  
corresponding setup program.  
Information for the driver installation is in the file:  
D:\TOUCH\MC15\TouchKit\Document\TouchKit Manual v3.1.4.pdf  
You can find detailed information in the path, named with your operating system. (The CD-  
ROM drive of your Tocuh-CD is here defined with the letter „D“).  
5. Care  
Before cleaning, switch off the power supply. A soft cloth moistened with a mild cleaning  
agent can be used for cleaning the housing. For cleaning the screen it is better to use a  
soft paper towel moistened with a mild household cleaning agent. For cleaning the surface  
do not apply the cleaning liquid directly but use a moistened paper towel. Please avoid  
getting liquid into the housing.  
6. Troubleshooting  
6.1 General Points  
Attention:  
The Preh Touch / Screen Commander does not contain any electronic components that  
can be replaced or repaired by the user. Consequently you should not try to do your own  
repair work. Moreover, you would lose all warranty claims for this product. Activating the  
touch sensor surface must not be done with a sharp object, such as credit card, long finger  
nails, ring, etc. Sharp or pointed objects will cause damage to the touch sensor and are  
not covered under warranty  
If the Touch/Screen Commander must be returned for service, it must be packed in it's  
original packing material. If this is not done, the sender will be made responsible for  
possible transport damage.  
14  
subject to change without prior notice  
05.2004  
 
6.2 Troubleshooting list  
A lot of malfunctions can be traced back to incorrect or loose cable connection. So  
please make sure that all plug connections are correct and secured.  
Fault  
Possible cause  
Remark  
LED on Touch / Screen  
Commander remains dark order  
voltage supply not in  
check plug-in connection of power  
supply  
computer switched off switch on the computer  
LED on Touch / Screen  
Commander lights up red  
and no picture appears  
The display shows only  
part of the picture or the  
picture is distorted  
VGA cable is not  
correctly connected  
check cable connection of VGA  
connection  
choice of display  
resolution is wrong  
display adjustment  
insufficient  
check for correct display resolution  
it should be 1024x768 or less  
see notice to adjustment of in  
chapter 3.3  
LCD shows indistinct  
vertical stripes  
display ("HORIZONTAL set horizontal size of picture in  
SIZE") is insufficiently menu IMAGE POSITION of  
set  
LCD shows fine horizontal display ("PHASE") is  
stripes not correctly adjusted  
OSD(see chapter 3.3.2)  
adjust PHASE in menu BASIC-  
SETTINGS of OSD (see chapter  
3.3.1)  
Touch cannot be calibrated cable connection  
check serial connection, restart  
computer  
under the operating  
systems of Windows,  
button "calibrate" is  
deactivated  
incorrect  
Vertical streaks in LCD  
image  
Display “Clock” or  
“Horizontal Position”  
improperly set  
Set horizontal position and size of  
picture in menu “H-Position”and  
“Clock” of OSD (see chapter 3.3.2)  
Calibrating program states touchscreen driver not Set the driver again with SETUP or  
error when called up  
correctly installed  
with button setup in the calibrating  
program. Here the serial connection  
should be correctly entered and the  
correct controller should be  
selected. Check the serial cable  
connection  
6.3 Additional help  
If you have problems with the connection and the installation of the Preh Touch / Screen  
Commander, please contact your dealer.  
You can contact Preh Technical Support at:  
Germany /world wide:  
Email:  
Fax:  
+49 (9771) 92-152  
USA/America:  
Email:  
Fax:  
+1 847-438-4053  
15  
subject to change without prior notice  
05.2004  
 
7. Technical Data  
7.1 Product Specification  
Configuration  
LCD Display  
Display Size  
Pixel Pitch  
Max. Resolution  
Contrast Ratio  
Brightness  
MC15T5XXM3MX  
15” TFT active matrix panel  
304(H)x228(V) mm  
0.297(H)x0.297(V) mm  
XGA 1024x768  
350:1  
250 cd/m2  
Response Time  
Display Color  
6/17 ms  
262,144  
Viewing Angle  
L/R  
60~ 60∘  
40~ 60∘  
39+/- 3∘  
40+/- 3∘  
U/D  
Swivelling  
Tilt  
PC Interface  
Display Mode  
Video  
Sync.  
RGB analog 0.7V peak to peak  
TTL positive or negative  
VGA 640x400 (60/70 HZ)  
VGA 640x480 (60/72/75 HZ)  
VGA 720x400 (70 HZ)  
SVGA 800x600 (60/70/72/75 HZ)  
XGA 1024x768 (60/70/72/75 HZ)  
D-sub 15 pin  
Signal Connector  
Front Control  
OSD  
Menu, Left, Power on/off with LED, Right, Select  
AutoTun, Brightness, Contrast, Color, Phase, H-POS, V-  
POS, OSD H-Pos, OSD V-Pos, Volume, Red Color, Blue  
Color, Green Color, Exit, Reset  
DDC1/2B compatible  
Plug & Play  
Speaker  
Power  
Active Speaker  
Input: AC 110-240 Volts, 47 – 63 Hz,  
Output: DC 12V/4A  
Operating  
Conditions  
Temperature  
0- 40(32- 104)  
20%~ 85%  
Humidity  
Storage  
Conditions  
Temperature  
-10- 60(-4- 140)  
Humidity  
5%~ 85%  
Life of background illumination  
Base Type  
Touch Screen  
Magnetic Stripe Reader  
Certification  
* Specifications are subject to change without notice.  
typ.40,000 h  
Multimedia / Wall Mount  
Option / RS232 Interface  
Option / Three tracks  
UL,CUL, FCC, TUV/GS, CE  
16  
subject to change without prior notice  
05.2004  
 
7.2 Electronics:  
Following specifications are for the multimedia model only:  
Line voltage:  
Power consumption  
100-240 AC, 47-63 Hz, 0.6A  
max. 20 W  
Following values are valid for the model VESA mount bracketry only:  
Operating Voltage:  
Ripple:  
Power Consumption  
12 V ± 5% (100-240VAC, 47-63Hz, 2.2A)  
< 120 mV  
max. 30W  
The values in brackets are for the power supply delivered with the Touch / Screen  
Commander.  
The Touch Commander / Screen Commander with VESA mount bracketry must be  
operated with the supplied original power supply or with power supplies which are  
approved by Preh.  
For use only with power Adapter:  
Vender1: LIEN CHANG Model: LCA01F  
I/P: 100-240 Vac, 47-63 Hz  
O/P: 12VDC/4.16A  
Vender2: CHI SAM Model: CH-1204  
I/P: 100-240 Vac, 47-63 Hz, 1A  
O/P: 12VDC/4.00A  
7.3 Touch:  
Interface:  
RS232, Mouse Emulation under DOS, Windows 3 x,  
Windows 9x, NT, 2000, XP, Linux and OS/2  
5-wire resistive  
max. 2048*2048  
hardcoated polyester foil  
75%  
Technology:  
Resolution:  
Surface:  
Transmission:  
Durability  
35 million actuation  
7.4 Touch Controller  
Controller:  
Power Requirement:  
Winbond W78E52F-24  
5V/100mA  
Operating Temperature: 0 to 50℃  
Storage Temperature:  
-40to 80℃  
Relative Humidity:  
95% at 60℃  
Interface:  
RS232  
Protocol:  
No parity, 8 data bit, 1 stop bit, 9600 baud (N, 8, 1, 9600)  
Report rate:  
Response time:  
Max. 160 points/sec  
Max. 35ms  
17  
subject to change without prior notice  
05.2004  
 
7.5 MSR (Option)  
Interface:  
Track:  
Decode:  
PS/2 key.  
Three Tracks  
KB Interface.  
Right Side scan.  
Scan direction:  
Power Supply:  
5V DC ±5%  
Power consumption:  
Durability:  
Card Spec:  
Less than 20mA  
500,000 cycle.  
ISO7811  
Reading Track Width:  
Card Feeding Speed:  
1.5mm  
10 ~ 120 cm/sec(4-50inch/sec)  
7.6 Audio  
Amplifier Controller:  
Output:  
TDA7496L  
2W/Ch.  
Power:  
Control Method:  
Frequency:  
12V/25mA  
PWM Adjust.  
20 ~ 20KHz  
7.7 ESD and EMC compliance  
CE-sign (see also Statement of confirmation)  
Radiated Emissions: EN55022, class B  
FCC part 15, class B  
Susceptibility  
Compliance:  
1. electrostatic discharge according to EN 61000-4-2  
(hardness air +,-8KV and contact +,- 4KV)  
2. high frequency electromagnetic fields EN 61000-4-3  
(hardness Modulation 3 V/m),  
3. fast transient/burst immunity electrical interference  
features according to EN 61000-4.4 (Criteria B:  
hardness 1 kV for AC power)  
4. Surge immunity test according to EN 61000-4-5  
(Criteria B)  
5. Immunity for conductive disturbance test according  
to EN61000-4-6(Criteria B: level is 3V Modulation)  
6. power frequency magnetic field test EN 61000-4-8  
(Criteria B: 1A/m)  
7. voltage dips , short interrupt and voltage variation  
immunity EN 61000-4-11(Criteria B)  
8. power harmonics test EN 61000-3-2(Criteria A:<=75W)  
9. voltage fluctuation test EN 61000-3-3  
7.8 Durability of mechanical bearing parts  
Tilting and swinging  
1.000 cycles typical  
18  
subject to change without prior notice  
05.2004  
 
7.9 Environmental conditions  
Operating amibent temperature:  
Storing temperature:  
Relative humidity of air:  
Air pressure:  
0°C...50°C  
-20°C...60°C  
10%...90% (at max. 35°C)  
700hPa...1060hPa  
8. Safety issues  
Please read these instructions carefully before connecting the unit to any AC-mains and  
keep the instructions also for later use.  
The multimedia type is belong to Class I type and the wall mount type is belong to Class III  
type for power consuming configuration.  
First check the power values of your AC-mains with the datas of this device, before  
connecting to any wall-plug socket.  
Place the unit as close as possible to your wall-plug socket and make sure, that the mains  
connector is easily accessable. Make also sure, that there are no other equipments placed  
on the cable and also that it’s placed in a way, that nobody can fell over it. If the unit is not  
in use for a longer period, it should be disconnected from mains.  
Protect the device from any liquids and high humidity. Do not operate the unit outdoors.  
Unplug the device from the wall-plug socket immediately and have it checked by a  
qualified Service person in case:  
the mains cable or connector is being damaged  
liquids have been penetrated into the device  
the device has been exposed to the elements (dampness/rain)  
the device does not operate as to the operating instructions  
the device has been dropped and / or shows outside damages (i.e. cabinet)  
the device shows markable performance of deffects  
Do not open the device on your own as there is dangerious voltage inside. Apply to the  
Service or your dealer for any repair issues.  
Do not drink liquid crystal leaking from the LCD in case of a damage. If such leakage  
touches your skin, clean it by water & soap, immediately.  
The working place related sound pressure level (DIN 45 645) of the device is less  
then70dB(A)  
It it only permitted to use tested / certified power cables H03VV-F.3G, 0.75 and / or better  
ones.  
The maximum environment temperature is 40 degrees Celsius  
GS and ISO 9241-7 for class III certified Screens will meet its classification under the  
following conditions:  
the operation of the screen complies to suitable working place illumination  
environment  
the screen shall not be placed in front of a window or direct light  
19  
subject to change without prior notice  
05.2004  
 
9. Further Information  
All Preh products are subject to a continuous process of improvement. For this reason we  
reserve the rights of technical modifications.  
We point out that inadequate handling, storage, influence and/or modification can cause  
disturbances and damage in usage.  
In case you modify our products in any way we do not assume warranty and liability unless  
you have an explicit release in writing for your specific case.  
This applies especially to unprofessional repair and maintenance jobs.  
Any claims for damages against the Preh works – no matter for which legal reason – are  
excluded if no intention and gross negligence can be proved. Above limitation do not apply  
to claims for damages out of the product liability law.  
This Operator's Manual is exclusively valid for the product Preh Touch / Screen  
Commander supplied with it.  
10. Warranty  
Preh guarantees that all products supplied are free from production and material faults.  
The period of warranty is two years and begins with the date of delivery.  
Otherwise the general sales conditions of the Preh company are valid.  
11. Statement of Confirmation  
This is to certify that statements of confirmation are available for all different versions of  
the Preh Touch / Screen Commander.  
You can request a copy from Preh stating the exact type description (see type label on the  
bottom of the device).  
Preh KeyTec GmbH  
An der Stadthalle  
D-97616 Bad Neustadt an der Saale  
Fax: +49 (9771) 92-105  
20  
subject to change without prior notice  
05.2004  
 
12. FCC Warning Statement  
Note: This equipment has been tested and to comply with the limits for Class B or Class A  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment on and off, the  
user is encouraged to try to correct the interference by one of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Shielded interface cables must be used in order to comply with the emission limits.  
Caution:  
Changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
Copyright  
© Copyright Preh KeyTec GmbH 2004  
Published from Preh KeyTec GmbH  
All rights reserved. Reproduction in any manner, in whole or in part, is strictly prohibited without the written permissin of Preh KeyTec  
GmbH. The Information in this document is subject to change without prior notification for the sake of improving reability, design and  
function.  
Trademarks  
All brand and product names are trademarks or registered trademarks of their respective companies.  
05.2004  
21  
subject to change without prior notice  
05.2004  
 

Philips CD Player 150X4 User Manual
Philips Digital Camera SIC4524BB User Manual
Philips Photo Printer 201P201P1010 User Manual
Philips Projection Television 43PP9202 User Manual
Philips Projector LC7281 User Manual
Polaroid Flat Panel Television PLA 4250A User Manual
Polaroid Portable Generator BLL Generator User Manual
Poulan Lawn Mower 173284 User Manual
ProForm Treadmill 400 GL User Manual
PYLE Audio MP3 Player PLCD13MR User Manual