R
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PPB1634
PPB1838
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2003 Electrolux Home Products, Inc.
530164284
11/14/03
S Carefully planyour sawingoperationin ad-
vance. Donot startcutting until you havea
clear work area, secure footing, and, if you
are felling trees, a planned retreat path.
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
S Storetheunitandfuel in anarea wherefuel
vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.
OPERATE YOUR SAW SAFELY
S Do notoperatea chain saw with one hand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion.
A
chain saw is intended for
two-handed use.
S Operatethe chain saw only in a well-venti-
lated outdoor area.
KICKBACK
S Do not operate saw from a ladder or in a
tree.
WARNING:
Avoid kickback which
S Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
can result in serious injury. Kickback is the
backward,upwardorsuddenforwardmotion
of the guide bar occurring when the saw
chain near the upper tip of theguide barcon-
tacts any object such as a log or branch, or
when the wood closes in and pinches the
saw chain in thecut. Contactinga foreignob-
ject in the wood can also result in loss of
chain saw control.
S Do not put pressure on the saw at the end
of the cut. Applying pressure can cause
you to lose control when the cut is com-
pleted.
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brake immediately if it becomes damaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.
S RotationalKickback can occur when the
moving chain contacts an object at the up-
per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to-
ward the operator.
S Pinch-Kickback can occur when the the
wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used to cut wood and causes the
saw tomovein theoppositedirection ofthe
chain rotation. The saw is driven straight
back toward the operator.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have all chain saw service performed by a
qualified service dealer with the exception
of the items listed in the maintenance sec-
tionofthis manual. Forexample, ifimprop-
er tools are used to remove or hold the fly-
wheel whenservicing theclutch, structural
damage to the flywheel can occur and
cause the flywheel to burst.
S Pull-In can occur when the moving chain
contacts a foreign object in the wood in the
cut along the bottom of the guide bar and the
saw chain is suddenly stopped. This sudden
stopping pulls the saw forward and away
from the operator and could easily cause the
operator to lose control of the saw.
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENTS.
S Never modify your saw in any way.
S Keep the handles dry, clean, and free of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only Poulan PROR accessories and
replacement parts as recommended.
Avoid Pinch -Kickback:
S Be extremely aware of situations or ob-
structions that can cause material to pinch
the top of or otherwise stop the chain.
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
Avoid Pull-In:
HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or while
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
Thereshould be nosmoking, openflames,
or work that couldcause sparks. Allow en-
gine to cool before refueling.
S Always begin cutting with the engine at full
speed and the saw housing against wood.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
ckback Path
S Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, well
ventilated place; and use an approved,
3
Avoid Obstructions
Elbow locked
Clear The Working Area
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
Thumb on underside of
handlebar
S Keepa good, firm gripon thesaw withboth
hands when the engine is running and
don’t let go. A firm grip will help youreduce
kickback and maintain control of the saw.
Keep the fingers of your left hand encir-
cling and your left thumb under the front
handlebar. Keep your right hand com-
pletely around the rear handle whether
your are right handedor left handed. Keep
your left arm straight with the elbow
locked.
S Position your left hand on the fronthandle-
bar so it is in a straight line with your right
hand on the rear handle when making
bucking cuts. Never reverse right and left
hand positions for any type of cutting.
S Standwithyour weightevenly balancedon
both feet.
S Stand slightly to the left side of the saw to
keep your body from being in a direct line
with the cutting chain.
S Do not overreach. You could be drawn or
thrown off balance and lose control of the
saw.
S Do not cut above shoulderheight. It is diffi-
cult to maintain control of saw above
shoulder height.
KICKBACK SAFETY FEATURES
S Never let themoving chaincontact any ob-
ject at the tip of the guide bar.
S Keep the working area free from obstruc-
tions suchas othertrees, branches,rocks,
fences, stumps, etc. Eliminate or avoid
any obstruction that your saw chain could
hit while you are cutting. When cutting a
branch, do not let the guide bar contact
branch or other objects around it.
S Keep your saw chain sharp and properly
tensioned. A loose or dull chain can in-
crease the chance of kickback occurring.
Follow manufacturer’s chain sharpening
and maintenanceinstructions. Check ten-
sion at regular intervals with the engine
stopped, never with the engine running.
Make sure the chain brake nuts are se-
curely tightenedafter tensioning thechain.
S Begin and continue cutting at full speed. If
the chain is moving at a slower speed,
there is greater chance of kickback occur-
ring.
S Cut one log at a time.
S Use extreme caution when re-entering a
previous cut.
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
S Watch for shifting logs or other forces that
could close a cut and pinch or fall into
chain.
WARNING: The following features
are included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this danger. As a
chain saw user, do not rely only on safety de-
vices. You must follow all safety precau-
tions, instructions, and maintenance in this
manual to help avoid kickback and other
forces which can result in serious injury.
S Reduced--Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced--Kickback Guide Bar
has been demonstratedto significantly re-
duce the number and seriousness of kick-
backs when tested in accordance with
safety requirements for gasoline powered
chain saws as set by ANSI B175.1.
S Use the Reduced--Kickback Guide Bar
and Low--Kickback Chain specified for
your saw.
MAINTAIN CONTROL
Stand to
left of th
Thumb on
underside of
handlebar
Never
hand positions
4
Reduced Kickback Symmetrical Guide Bar
caused by allowing contact of the bar tip in the
danger zone with any hard object. Kickback
can also be caused by pinching the saw chain
along the top of the guide bar. This action may
push the guide bar rapidly back toward the op-
erator. Either of these events may cause you
to lose control of the saw which could result in
serious injury or even death. DO NOT RELY
UPON ANY OF THE DEVICES BUILT INTO
YOUR SAW. YOU SHOULD USE THE SAW
PROPERLY AND CAREFULLY TO AVOID
KICKBACK. Reduced--kickback guide bars
and low--kickback saw chains reduce the
chance and magnitude of kickback and are
recommended. Your saw has a low kickback
chain and bar as original equipment. Repairs
on a chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a servic-
ing dealer, or to the nearest authorized master
service dealer.
Small Radius Tip
Symm
Large Radius Tip
S Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride intothe cutter. Low--
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
S Tip contact in some cases may cause a light-
ning fast reverse REACTION, kicking guide
bar up and back toward operator.
Contoured Depth Gauge
S Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
S Either of these reactions may cause you to
lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices built into your saw.
Elongated Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
Low---Kickback
Chain
WARNING:
Computed kickback
angle (CKA) listed on your saw and listed in the
CKA table below represents angle of kickback
your bar and chain combinations will have
when tested in accordance with CSA (Cana-
dian Standards Association) and ANSI stan-
dards. When purchasing replacement bar and
chain, considerations should be given to the
lower CKA values. Lower CKA values repre-
sent safer angles to the user, higher values in-
dicate more angle and higher kick energies.
Computed angles represented indicate total
energy and angle associated without activation
of the chain brake during kickback. Activated
angle represents chain stopping time relative to
activation angle of chain break and resulting
kick angle of saw. In all cases lower CKA val-
ues represent a safer operating environment
for the user.
Can Obstruct Material
Not a Low---Kickback Chain
S Front Hand Guard, designed to reduce the
chance of your left hand contacting the chain
if your hand slips off the front handlebar.
S Position of front and rear handlebars, de-
signed with distancebetweenhandlesand
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
S Chain Brake, designed to stop the chain in
the event of kickback.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
WARNING: WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A KICK-
BACK. Kickback is a lightning fast action
which throws the bar and rotating chain back
and up toward the operator. Kickback can be
Computed kickback angle (CKA) Table
BAR
LE SERIES
MODEL
P/N
Length
16!
CHAIN P/N
952051547
952051548
CKA without chain brake
19_
PPB1634
PPB1838
952044370
952044418
18!
14_
5
The chain is sharp and can cut you even when
it is not moving!
1. Loosen and remove the chain brake
nuts and the chain brake from the saw.
2. Remove the plastic shipping spacer (if
present).
NOTE: If this saw is to be used for com-
mercial logging, a chain brake is required
and shall not be removed or otherwise dis-
abled to comply with Federal OSHA Regula-
tions for Commercial Logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin color or texture,
or loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the
condition of this tool.
SPECIALNOTICE:Yoursaw is equipped
with a temperaturelimiting muffler and spark
arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwith aspark arrestingscreen.
If you operatea chain saw in a state or locale
wheresuch regulations exist, you arelegally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
section for maintenance of the spark
arresting screen.
Location of shipping spacer
Chain Brake
Nuts
Chai
Bar Tool
3. An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar. Turning the screw will
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
illustration below.
ide view of
ain Brake
Adjustment located on Chain Brake
Failureto followall SafetyRules andPrecau-
tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.
4. Turn the adjusting screw by hand coun-
terclockwise until the adjusting pin just
touches the stop. This should allow the
pin to be near the correct position.
5. Slide guide bar behind clutch drum until
guide bar stops against clutch drum
sprocket.
STANDARDS: This saw is listed by Under-
writer’s Laboratories, Inc., in accordance with:
ANSI B175.1-2000 American National
Standards for Gasoline--Powered Chain
Saws -- Safety Requirements
CSA Z62.1-03 Chain Saws -- Occupational
Health and Safety
CSA Z62.3-96 Chain Saw Kickback Occu-
pational Health and Safety
Mount the Bar
6. Carefully remove the chain from the pack-
age. Hold chain with the drive links as
shown.
ASSEMBLY
Tip of
Bar
Protective gloves (not provided) should be
worn during assembly.
ATTACHINGTHEBAR& CHAIN(If not
already attached)
WARNING: If received assembled,
repeat all steps to ensure your saw is properly
assembled and all fasteners are secure. Al-
ways wear gloves when handling the chain.
CUTTERS MUST FACE IN
DIIRECTION OF ROTATION
6
Depth Gauge
Cutters
Checking the tension:
Use the screwdriver end of the chain adjust-
ment tool (bar tool) to move the chain around
the bar. If the chain does not rotate, it is too
tight.Iftoo loose, thechain will sag belowthe
bar.
Drive Links
Chain Adjustment
Tool (Bar Tool)
Chain Brake Nuts
Adjusting the tension:
Place chain onto the sprocket
7. Place chain over and behind clutch, fit-
ting the drive links in the clutch drum
sprocket.
8. Fit bottom of drive links between the
teeth in the sprocket in the nose of the
guide bar.
9. Fit chain drive links into bar groove.
10. Pull guide bar forward until chain is snug
in guide bar groove. Ensure all drive
links are in the bar groove.
Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.
You can adjust the chain tension by loosen-
ing the chain brake nuts and turning the ad-
justing screw 1/4 of a turn while lifting up on
the bar.
S Ifchainis tootight, turnadjusting screw 1/4
turn counterclockwise.
S If chain is too loose, turn adjusting screw
1/4 turn clockwise.
NOTE: CHAIN BRAKE MUST BE
DISENGAGED BEFORE INSTALLA-
TIONON THESAW. TO DISENGAGE
CHAIN BRAKE, PULL THE FRONT
HAND GUARD BACK TOWARD THE
REAR OF THE CHAIN BRAKE AS
FARASPOSSIBLE(SEEILLUSTRA-
TION).
Guide Bar
Adjusting Screw -- 1/4 Turn
Chain Brake Nuts
DISENGAGED
Front Hand Guard
S Lift up the tip of the bar and tighten the
chain brake nuts with the bar tool.
S Recheck chain tension.
NGAGED
Chain Brake
11. Now, install chain brake making surethe
adjusting pin is positioned in the lower
hole in the guide bar. Rememberthis pin
moves thebar forwardand backward as
the screw is turned.
12. Install chain brake nuts and finger tight-
en only. Once the chain is tensioned,
you will needto tightenchain brakenuts.
WARNING: If the saw is operated
with a loose chain, the chain could jump off
the guide bar and result in serious injury.
CHAIN TENSION
(Including units with chain already installed)
NOTE: When adjusting chain tension,
make sure the chain brake nuts are finger
tight only. Attempting to tension the chain
when the chain brake nuts are tight can
cause damage.
7
OPERATION
KNOW YOUR CHAIN SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of
the various controls and adjustments. Save this manual for future reference.
Front Handle
Front Hand Guard
Starter Rope
ON/STOP
Switch
Muffler
Chain
Primer
Bulb
Starter
Housing
Bar Oil Fill Cap
Fuel Mix Fill Cap
Cylinder Cover
Throttle
Lockout
Chain
Direction
of Travel
Adjusting
Screw
Rear
Handle
Guide Bar
Chain Brake
Nuts
Throttle
Trigger
Choke/
Fast Idle
Lever
Chain
Chain
Bar Sprocket Hole
Catcher
Brake
ON/STOP SWITCH
CHAIN BRAKE
The ON/STOP SWITCH is used to stop the
engine.
The CHAIN BRAKE is a device designed to
stop the chain if kickback occurs. The chain
brake activates automatically in the event of
kickback. The chain brake activates manually
if the front hand guard is pushed forward. The
chain brake is disengaged by pulling the front
hand guard back toward the front handle as far
as possible.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed.
THROTTLE LOCK--OUT
The THROTTLE LOCK--OUT must be
pressed before you can squeeze the throttle
trigger. This feature prevents you from acci-
dentally squeezing the trigger.
CHAIN TENSION
It is normal for a new chain to stretch during the
first 15 minutes of operation. You should check
your chain tension frequently. See CHAIN
TENSION under the ASSEMBLY section.
CHOKE/FAST IDLE LEVER
The choke and fast idle are set by pulling the
CHOKE/FAST IDLE LEVER out to the full ex-
tent for cold starting or after refueling. The
choke provides additional fuel to the engine
during cold starting.
WARNING: Muffler is very hot dur-
ing and after use. Do not touch the muffler or
allow combustible material such as dry
grass or fuel to do so.
PRIMER BULB
The PRIMER BULB circulates fuel to the car-
buretor to provide quicker starting.
8
FUELING & LUBRICATION
STARTING
WARNING: The chain must not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR ADJUSTMENT within this
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
WARNING: Remove fuel cap slow-
ly when refueling.
FUELING ENGINE
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. A 40:1
ratio is obtainedby mixing 3.2ounces (95ml)
of oil with 1 gallon (4 liters) of unleaded gaso-
line. Included with this saw is a 3.2 ounce con-
tainer of Poulan/Weed Eater brand synthetic
oil. Pour the entire contents of this container
into 1 gallon of gasoline to achieve the proper
fuel mixture.
To stop the engine move the ON/STOP
switch to the STOP position.
To start the engine hold the saw firmly on the
ground as illustrated. Make sure the chain is
free to turn without contacting any object.
Use only 15! -- 1 8 ! (38 -- 45 cm) of
rope per pull.
Hold saw firmly while pulling starter rope.
Starter Rope Handle
Left Hand
on Front
Handle
DO NOT USE automotive or marine oil.
Theseoils will cause engine damage. When
mixing fuel follow the instructions printed on
the container. Always read and follow the
safety rules listed under HANDLE FUEL
WITH CAUTION.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shownby smoke coming from the chain and/
or discoloration of the bar.
In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enough oil
for adequate lubrication.
Right Foot Through Rear Handle
IMPORTANT POINTS TO REMEMBER
Whenpullingthestarter rope, donot use thefull
extent of the rope as this can cause the rope to
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold weather starting, start the unit at
FULL CHOKE; allow the engine to warm up
before squeezing the throttle trigger.
NOTE: Do not attempt to cut material with
the choke/fast idle lever in theFULLCHOKE
position.
STARTING A COLD ENGINE (or warm
engine after running out of fuel)
Genuine Poulan or Poulan PROR bar and
chain oil is recommended to protect your unit
against excessive wear from heat and friction.
NOTE: In the following steps, when the
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
Poulan or Poulan PROR
temperature thinning.
oil resists high
If Poulan or Poulan PROR bar and chain oil
is not available, use agoodgradeSAE 30oil.
ON/STOP SWITCH
S Never use waste oil for bar andchain lubri-
(SIDE VIEW)
cation.
S Always stop the engine before removing
ON
the oil cap.
IMPORTANT
STOP
Experience indicates that alcohol--blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage for 30
days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next
season. See STORAGE section for addi-
tional information.
1. Move ON/STOP switch to the ON posi-
tion.
2. Pull choke/fast idle lever out to the full
extent (to the FULL CHOKE position).
3. Slowly press primer bulb 6 times.
4. Pull the starter rope sharply 5 times with
your right hand. Then, proceed to the
next step.
NOTE: If the engine sounds as if it is trying
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
9
5. Push the choke/fast idle lever in to the
HALF CHOKE position.
S When cutting with the saw, the chainbrake
must be disengaged.
Disengaged
CHOKE/FAST IDLE LEVER
(SIDE VIEW)
Engaged
Choke/
Braking function control
fast idle lever
OFF HALF FULL
CAUTION: The chain brake must be
checked several times daily. The engine
must berunningwhenperformingthis proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine running.
6. Pull the starter rope sharply with your
right hand until the engine starts.
7. Allow the engine to run for approximate-
ly 5 seconds. Then, squeeze and re-
lease the throttle trigger to allow engine
to return to idle speed.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthe fronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON posi-
tion.
2. Pull the choke/fast idle lever out to the
HALF CHOKE position.
3. Slowly press primer bulb 6 times.
4. Pull the starter rope sharply with your
right hand until the engine starts.
5. Squeeze and release throttle trigger to
allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
Inertia activating function control
WARNING: When performing the
following procedure, the engine must be
turned off.
Grip the rear handlewith your right hand and
the front handle with your left hand. Hold the
chain saw approximately 14! (35 cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
completely (to the OFF CHOKE position)
and then following the warm engine starting
procedure listed above. Ensure the ON/
STOP switch is in the ON position.
Startingcould require pulling the starter rope
handle many times depending on how badly
theunit is flooded. Ifenginefails to start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
CUTTING METHODS
IMPORTANT POINTS
S Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
CHAIN BRAKE
WARNING: If the brake band is
worn too thin it may break when the chain
brakeis triggered.With abrokenbrakeband,
the chain brake will not stop the chain. The
chain brake should be replacedby an autho-
rized service dealer if any partis worntoless
than 0.020! (0.5 mm) thick. Repairs on a
chain brake should be made by an autho-
rized service dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
and thus increase the possibility of kickback.
S Practice cutting a few small logs using the
following techniques to get the “feel” of us-
ing your saw before you begin a major
sawing operation.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S
Squeeze the throttle trigger and allow
the engine to reach full speed before
cutting.
Begin cutting with the saw frame
against the log.
Keep the engine at full speed the entire
time you are cutting.
Allow thechaintocut foryou. Exertonly
light downward pressure. If you force
thecut, damageto the bar, chain, oren-
gine can result.
S The inertia--activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedby pulling thefronthandguard
back toward the front handle as far as
possible.
S
S
S
10
S
S
Release the throttle trigger as soon as
the cut is completed, allowing the en-
gine to idle. If you run the saw at full
throttlewithout a cutting load,unneces-
sary wear can occur to the chain, bar,
and engine. It is recommended that
the engine not be operated for lon-
ger than 30 seconds at full throttle.
Toavoidlosing controlwhencut is com-
plete,donotputpressureonsaw atend
of cut.
FELLING LARGE TREES
(6 inches (15cm) in diameter or larger)
The notch method is used to fell large trees.
A notch is cut on the side ofthe treein thede-
sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
NOTE: If the tree has large buttress roots,
remove them beforemaking the notch. If us-
ing saw to remove buttress roots, keep saw
chain from contacting groundto preventdull-
ing of the chain.
S Stop the engine before setting the saw
down after cutting.
NOTCH CUT AND FELLING THE
TREE
TREE FELLING TECHNIQUES
S Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
ofthetree. Nextcomplete thenotch by cut-
ting the bottom of the notch. See illustra-
tion. Once the notch is cut remove the
notch of wood from the tree.
WARNING: Check for broken or
dead branches which can fall while cutting
causing serious injury. Do notcut nearbuild-
ings or electrical wires if you do not know the
direction of treefall, norcut atnight since you
will not be ale to see well, nor during bad
weathersuch as rain, snow, or strong winds,
etc. If the tree makes contact with any utility
line, the utility company should be notified
immediately.
Final (felling) cut here, 2 inches
(5 cm) above center of notch.
First cut
Notch
S Carefully planyour sawingoperationin ad-
vance.
S Clear theworkarea. You needa clear area
all aroundthe treeso you can have secure
footing.
S The chain saw operator should keep on
the uphill side of the terrain as the tree is
likely toroll or slide downhill afterit is felled.
S Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree to
fall in a particular direction include:
Hinge
Second cut
S After removing the wood from the notch,
make the felling cut on the opposite side of
the notch. This is done by making a cut about
two inches (5 cm) higher than the center of
the notch. This will leave enough uncut wood
between the felling cut and the notch to form
a hinge. This hinge will help prevent the tree
from falling in the wrong direction.
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or level to de-
termine the direction of tree lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
Look for decay and rot. If the trunk is rotted,
it can snap and fall toward the operator.
Check for broken or dead branches which
can fall on you while cutting.
Make sure there is enough room for the tree
to fall. Maintain a distance of 2-1/2 tree
lengths from the nearest person or other ob-
jects. Engine noise can drownout a warning
call.
Hinge holds tree on stump and helps
control fall
Opening
of felling
cut
Remove dirt, stones, loose bark, nails, sta-
ples, andwire from the treewherecuts areto
be made.
Plan a clear retreat pathto the rear and diag-
onal to the line of fall.
Closing of
notch
NOTE: Before felling cut is complete, use
wedges to open the cut if necessary to
controlthedirectionoffall. To avoid kickback
and chain damage, use wood or plastic
wedges, but never steel or iron wedges.
S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell-
ing cut, or movement in the upper
branches.
Plan a clear retreat path
Direction of Fall
45_
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
11
S DO NOT cut down a partially fallen tree
with your saw. Be extremely cautious with
partially fallen trees that may be poorly
supported. When a tree doesn’t fall com-
pletely, setthesaw aside andpull downthe
tree with a cable winch, block and tackle,
or tractor.
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
WARNING: Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
Always make your first cut on the compres-
sion side of thelog. Thecompression sideof
the log is where the pressure of the log’s
weight is concentrated.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log size.
First cut on compression side of log
WARNING: Do not stand on the log
being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully; sharp
pieces of wood could be flung toward opera-
tor.
Second cut
Second cut
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting andnever hold the log with your leg
or foot.
S Do not cut in an area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs into a clear area
before cutting by pulling out exposed and
cleared logs first.
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
S Watch for logs with a compression side to
prevent the saw from pinching. See il-
lustrations for cutting logs with a compres-
sion side.
TYPES OF CUTTING USED FOR
BUCKING
WARNING:
If saw becomes
pinched or hung in a log, don’t try to force it
out. You can lose control ofthe saw resulting
in injury and/or damage to the saw. Stop the
saw, drive awedgeofplastic or woodintothe
cut until the saw can be removed easily. Re-
startthesaw andcarefully reenterthecut. To
avoid kickback and chain damage, do not
use a metal wedge. Do notattempt to restart
your saw when it is pinched or hung in a log.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on the
compression side of the log.
(Refer to the illustrations below for your
first and second cut)
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
Use a wedge to remove pinched saw
Using a log for support
nd
2
Cut
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting begins on the top side of the log
with the bottom of the saw against the log.
When overcutting use light downward pres-
sure.
st
1
Cut
Overcutting
st
1
Cut
Und
Undercuttinginvolves cutting on the under-
side of thelog with top of saw against thelog.
When undercutting use light upward pres-
nd
2
Cut
12
S Remove larger, supporting branches with
the cutting techniques described in BUCK-
ING WITHOUT A SUPPORT.
Using a support stand
nd
2
Cut
S Always use an overcut to cut small and free-
ly hanging limbs. Undercutting could cause
limbs to fall and pinch the saw.
PRUNING
st
1
Cut
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoulder. Get a
professional to do the job.
S Make your first cut 1/3 of the way through the
bottom of the limb.
st
1
Cut
S Next make a 2nd cut all the way through
the limb. Thencuta thirdovercut leavinga
1to2inch (2.5to5cm) collar from thetruck
of the tree.
nd
2
Cut
Second cut
Third cut
LIMBING AND PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branches or objects
at the nose of the guide bar when limbing or
pruning. Allowing such contact can result in
serious injury.
Collar
First cut
Pruning technique
WARNING: Never climb into a tree to
limb or prune. Do not stand on ladders, plat-
forms, a log, or in any position which can cause
you to lose your balance or control of the saw.
SERVICE
IMPORTANT POINTS
S Work slowly, keeping both hands firmly
gripped on the saw. Maintain secure footing
and balance.
S Watch out for springpoles. Springpoles are
small size limbs which can catch the saw
chain and whip toward you or pull you off bal-
ance. Use extreme caution when cutting
small size limbs or slender material.
S Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
saw when the tension in the wood fibers is
released.
WARNING:
Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.
MAINTENANCE SCHEDULE
Check:
Fuel mixture level . . . . Before each use
Bar lubrication . . . . . . . Before each use
Chain tension . . . . . . . Before each use
Chain sharpness . . . . Before each use
For damaged parts . . Before each use
For loose caps . . . . . . Before each use
For loose fasteners . . . Before each use
For loose parts . . . . . . Before each use
Inspect and Clean:
S Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
LIMBING
S Always limb atreeafter it is cutdown. Only
then can limbing be done safely and prop-
erly.
Bar . . . . . . . . . . . . . . . . Before each use
Complete saw . . . . . . . After each use
Air filter . . . . . . . . . . . . . Every 5 hours*
Chain brake . . . . . . . . Every 5 hours*
Spark arresting screen
S Leave the larger limbs underneath the felled
tree to support the tree as you work.
S Start at the base of the felled tree and work
toward the top, cutting branches and limbs.
Remove small limbs with one cut.
S Keep the tree between you and the chain.
Cut from the side of the tree opposite the
branch you are cutting.
and muffler . . . . . . . . . Every 25 hours*
Replace spark plug . Yearly
Replace fuel filter . . . Yearly
* Hours of Operation
13
2. Remove the bolt cover.
AIR FILTER
3. Loosen and remove the 2 muffler bolts.
Remove the muffler, muffler gasket, out-
let guide and backplate. Notice the ori-
entationof these parts forreassembling.
4. Locate the 2 outlet cover screws on the
CAUTION: Do not clean filter in gasoline
or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora-
tive emissions.
Cleaning the air filter:
muffler.
screws.
Loosen and remove both
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
5. Remove the outlet cover.
Outlet Cover
BACK VIEW OF
MUFFLER
1. Loosen 3 screws on cylinder cover.
2. Remove cylinder cover.
Muffler
3. Remove air filter.
Screws
4. Clean the air filter using hot soapywater.
Rinse with clean cool water. Air dry
completely before reinstalling.
Spark Arresting
Screen
5. Lightly oil air filter before installing to im-
prove the efficiency of air filter. Use
2--cycle engine oil or motor oil (SAE 30).
Squeeze excess oil from filter.
6. Reinstall air filter.
6. Remove spark arresting screen.
7. Clean the spark arresting screen with a
wire brush. Replace screen if any wires
are broken or screen is blocked after clea-
ning.
8. Reinstall spark arresting screen.
9. Reinstall outlet cover and 2 screws. En-
sure outlet cover and both screws are
reinstalled correctly (see illustrations) to
prevent damage to the saw. The ex-
haust outlet must face the chain brake
(bar side) of the saw.
7. Reinstall cylinder cover and 3 screws.
TIghten securely.
Cylinder Cover
Screws
Air Filter
Cylinder
Cover
Outlet Cover
Exhaust
Outlet
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
Exhaust Outlet must face chain
brake (bar side) of chain saw
WARNING:
The muffler on this
product contains chemicals known to the
State of California to cause cancer.
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removedto avoid creating a fire
hazard or affecting engine performance.
Replace the spark arresting screen if breaks
occur.
10. Inspect the muffler gasket and replace if
damaged.
11. Reinstall backplate, outlet guide, muffler
gasket, and muffler using muffler bolts.
Tighten until secure.
12. Reinstall boltcover andlocknut. Tighten
securely.
CARBURETOR ADJUSTMENT
CLEANING THE SPARK ARREST-
ING SCREEN
Cleaning is required every 25 hours of op-
eration or annually, whichever comes first.
WARNING: The chain will be mov-
ing during most of this procedure. Wear your
protective equipment and observe all safety
precautions. Thechain must notmove atidle
speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:
Outlet
Guide
S Chain moves at idle. See IDLE SPEED--T
Muffler
Muffler
adjusting procedure.
S Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
Backplate
Bolts
Idle Speed--T
Muffler
Gasket
Allow engine to idle. If the chain moves, idle
is toofast. Iftheenginestalls, idle is tooslow.
Adjust speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). Theidle speed screw is located in the
area above the primer bulb and is labeled T.
Bolt Cover
Locknut
1. Loosenand remove the locknut from the
bolt cover.
14
S Turn idle speed screw (T) clockwise to in-
crease engine speed.
1. Loosen 3 screws on cylinder cover.
2. Remove the cylinder cover.
3. Pull off the spark plug boot.
4. Remove spark plug from cylinder and
discard.
5. Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench. Spark plug gap
should be 0.025 inch (0.6 mm).
6. Reinstall the spark plug boot.
S Turn idle speed screw (T) counterclock-
wise to decrease engine speed.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized
service
dealer
or
call
1--800--554--6723.
BAR MAINTENANCE
If your saw cuts to oneside, has to be forced
throughthe cut, or beenrun with animproper
amount of bar lubrication it may be neces-
sarytoservice yourbar. A wornbarwill dam-
age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
7. Reinstall the cylinder cover and
screws. Tighten securely.
3
Cylinder
Screws
Cover
Spark
Plug Boot
Spark
Plug
S Move ON/STOP switch to the STOP posi-
tion.
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
STORAGE
S Clean the oil holes and bar groove after
each 5 hours of operation.
WARNING: Stop engine and allow
to cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Storeunitwithall guards in place. Positionso
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
Remove Sawdust From
Guide Bar Groove
Oil Holes
S Before storing, drain all fuel from the unit.
Start engine and allow to run until it stops.
S Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.
S Donotstore theunit orfuel in a closed area
where fuel vapors can reach sparks or an
openflamefrom hotwater heaters,electric
motors or switches, furnaces, etc.
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
S Store in a dry area out of the reach of chil-
dren.
Replace guide bar when the groove is worn,
the guide bar is bent or cracked, or when exce-
ss heating or burring of the rails occurs. If re-
placement is necessary, use only the guide bar
specified for your saw in the repair parts list or
on the decal located on the chain saw.
CAUTION: It is important to prevent gum
deposits from forming in essential fuel system
parts such as the carburetor, fuel filter, fuel
hose, or fuel tank during storage. Alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads
to fuel mixture separation and formation of
acids during storage. Acidic gas can damage
the engine.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener.
NEED ASSISTANCE?
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
NEED ASSISTANCE?
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.
Call 1--800--554--6723.
NEED SERVICE PART?
Contact your dealer or place of purchase.
15
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of
the recommendedremedies below except remedies that require operationof the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start or will run
only a few
seconds after
starting.
1. Move ignition switch to ON.
2. See “Difficult Starting” in
Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Ignition switch off.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
1. Idle speed requires
adjustment.
2. Carburetor requires
adjustment.
Engine will
not idle
properly.
1. See “Carburetor Adjustment” in the
Service and Adjustments Section.
2. Contact an authorized service dealer.
1. Clean or replace air filter.
Engine will not 1. Air filter dirty.
2. Clean or replace plug and regap.
3. Disengage chain brake.
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Chain brake engaged.
4. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
Engine
smokes
1. Too much oil mixed with
gasoline.
1. Empty fuel tank and refill with
correct fuel mixture.
excessively.
1. Idle speed requires
adjustment.
2. Clutch requires repair.
1. See “Carburetor Adjustment” in the
Service and Adjustments Section.
2. Contact an authorized service dealer.
Chain moves
at idle speed.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each
new Poulan PROr brand gasoline chain
saw is free from defects in material and
workmanshipandagrees torepair or replace
under this warranty any defective gasoline
chain saw as follows from theoriginal date of
purchase.
ty does not cover predelivery set--up, instal-
lation of guide bar and chain, and normal ad-
justments explained in the instruction
manual such as carburetor adjustments and
chain tension adjustments. This warranty
does not cover transportation costs.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
1 YEAR - Parts and Labor, when used for
Household purposes.
60 DAYS - Parts and Labor, when used for
Commercial, Professional, or Income Pro-
ducing purposes.
30 DAYS - Parts andLabor, if used forrental
purposes.
This warranty is not transferable and does
not cover damage or liability caused by im-
proper handling, improper maintenance, or
the use of accessories and/or attachments
not specifically recommended by ELEC-
TROLUXHOME PRODUCTS, INC., for this
chain saw. Additionally, this warranty does
not cover damage caused by improper han-
dling, improper maintenance, or if the saw is
alteredinany way which in our judgementaf-
fects its conditionor operation.This warranty
does not cover tune--up, spark plugs, filters,
starterropes,startersprings, chainsharpen-
ing, bars, chains, andotherparts which wear
and require replacement with reasonable
use during the warranty period. This warran-
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIEDWAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU.
The policy of ELECTROLUX HOME PRO-
DUCTS, INC., is to continuously improve its
products. Therefore,ELECTROLUXHOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obliga-
tion to any purchaser.
16
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
TIONS: The U.S. Environmental Protection
Agency, California Air Resources Board, Envi-
ronment Canada and ELECTROLUX HOME
PRODUCTS, INC., are pleased to explain the
emissions control system warranty on your
year 2002--2004 small off--road engine. In Cali-
fornia, all small off--road engines must be de-
signed, built, and equipped to meet the State’s
stringent anti--smog standards. ELECTRO-
LUX HOME PRODUCTS, INC., must warrant
the emission control system on your small off--
road engine for the periods of time listed below
provided there has been no abuse, neglect, or
improper maintenance of your small off--road
engine engine. Your emission control system
includes parts such as the carburetor and the
ignition system. Where a warrantable condition
exists, ELECTROLUX HOME PRODUCTS,
INC., will repair your small off--road engine en-
gine at no cost to you. Expenses covered un-
der warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVER-
AGE: If any emissions related part on your en-
gine (as listed under Emissions Control War-
ranty Parts List) is defective or a defect in the
materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
ELECTROLUX HOME PRODUCTS, INC.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the small off--road engine engine
owner, you are responsible for the perfor-
mance of the required maintenance listed in
your instruction manual. ELECTROLUX
HOME PRODUCTS, INC., recommends that
you retain all receipts covering maintenance on
your small off--road engine, but ELECTROLUX
HOME PRODUCTS, INC., cannot deny war-
ranty solely for the lack of receipts or for your
failure to ensure the performance of all sched-
uled maintenance. As the small off--road en-
gine engine owner, you should be aware that
ELECTROLUX HOME PRODUCTS, INC.,
may deny you warranty coverage if your small
off--road engine engine or a part of it has failed
due to abuse, neglect, improper maintenance,
unapproved modifications, or the use of parts
not made or approved by the original equip-
ment manufacturer. You are responsible for
presenting your small off--road engine to an
ELECTROLUX HOME PRODUCTS, INC.,
authorized repair center as soon as a problem
exists. Warranty repairs should be completed
in a reasonable amount of time, not to exceed
30 days. If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call ELECTROLUX HOME PROD-
UCTS, INC., at 1--800--554--6723. WARRAN-
TY COMMENCEMENT DATE: The warranty
period begins on the date the small off--road
engine is purchased. LENGTH OF COVER-
AGE: This warranty shall be for a period of two
years from the initial date of purchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved ELEC-
TROLUX HOME PRODUCTS, INC., servic-
ing center. If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call ELECTROLUX HOME PROD-
UCTS, INC., at 1--800--554--6723. WARRAN-
TY PERIOD: Any warranted part which is not
scheduled for replacement as required mainte-
nance, or which is scheduled only for regular
inspection to the effect of “repair or replace as
necessary” shall be warranted for 2 years. Any
warranted part which is scheduled for replace-
ment as required maintenance shall be war-
ranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be charged
for diagnostic labor which leads to the deter-
mination that a warranted part is defective if the
diagnostic work is performed at an approved
ELECTROLUX HOME PRODUCTS, INC.,
servicing center. CONSEQUENTIAL DAM-
AGES: ELECTROLUX HOME PRODUCTS,
INC., may be liable for damages to other en-
gine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov-
ered. ADD-ON OR MODIFIED PARTS: The
use of add--on or modified parts can be
grounds for disallowing
a
warranty claim.
ELECTROLUX HOME PRODUCTS, INC., is
not liable to cover failures of warranted parts
caused by the use of add--on or modified parts.
HOW TO FILE A CLAIM: If you have any
questions regarding your warranty rights and
responsibilities, you should contact your near-
est authorized service center or call ELEC-
TROLUX HOME PRODUCTS, INC., at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all ELECTROLUX
HOME PRODUCTS, INC., service centers.
Call: 1--800--554--6723 MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any ELECTROLUX
HOME PRODUCTS, INC., approved replace-
ment part used in the performance of any war-
ranty maintenance or repair on emission re-
lated parts will be provided without charge to
the owner if the part is under warranty. EMIS-
SION CONTROL WARRANTY PARTS LIST:
Carburetor, Ignition System: Spark Plug (cov-
ered up to maintenance schedule), Ignition
Module, Muffler including catalyst. MAINTE-
NANCE STATEMENT: The owner is responsi-
ble for the performance of all required mainte-
nance as defined in the instruction manual.
17
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
18
|