ELITE
ELITE.65CS
OWNER’S MANUAL
ELITE.65 Owner’s Manual
TWeeter Mounting
Threaded Retaining Nut
Mounting Baffle Area
One Piece Aluminum Housing
Installation Instructions:
1. Find a proper mounting location that is flat and has a mounting depth
clearance of roughly 21mm.
2. Cut a 47mm mounting hole in the door panel or mounting baffle.
3. Mount and secure the tweeter to the door panel or baffle using the
threaded retaining nut.
4. Connect the tweeter wires to the amplifier.
TWEETER WIRING NOTE:
BLACK = POSITIVE (+)
BLACK W/WHITE STRIPE = NEGATIVE (-)
Specifications
FEATURES:
• 25mm Silk Dome Tweeter
T/S Parameters:
Re (Dcr)
FS (Hz)
ELITE.65cs
3.6
• Fully Machined Aluminum Tweeter Housing
• Dampened Polypropylene Cone
• Smooth Termination Dual Roll Rubber Surround
• Powder Coated Diecast Aluminum Basket
• Custom Tooled Crossover Housing with Direct Wiring Con-
nections
• Audiophile Crossover with Tweeter and Midbass Adjustments
• Two Stage Light Bulb Tweeter Protection Circuitry
• Integrated Phase Plug
55
Sd (SqM)
BL TM
.0135
5.5
Qms
5.38
Qes
.607
Qts
.545
Vas (liters)
Cms (uM/N)
13.24
581.08
15.26
• Interwoven Tinsel Leads
Mms (gms)
• High Temperature CAE/CAD Motor Structure
*Midrange Driver Only
**Specifications subject to change
Note on Fully Active Crossover Systems: For the best performance we
always recommend the use of the provided passive crossovers with an
Specifications:
ELITE.65cs
external high pass electronic crossover usually located on the amplifier
or headunit. The passive crossover design is extremely complex as
it “blends” and “smoothes” the tweeter and midrange’s response and
impedances together.
RMS Power Handling
150 watts
300 watts
PEAK Power Handling
Running the system fully active with an external electronic crossover
(instead of the passive crossovers) for the tweeter and midrange
eliminates all this smoothing and transitional circuitry. The reality is that it
almost guarantees worse performance unless the system is perfectly EQ’d
with precision crossover points. It also eliminates the tweeter protection.
Unless you are sound quality and tuning expert, using the provided
crossovers will deliver the best performance.
Nominal Impedance
4 ohms
Tweeter HP Acoustical Crossover
Midrange LP Acoustical Crossover
3.5kHz @ 24dB (LnkRly)
2.95kHz @ 12dB (BTW)
(Mounting and Physical Dimensions are located on the back page)
DIMENSIONS
Tweeter depth measurement provides
extra space for protruding speaker wire
that is not shown.
(Mounting Hole Cutout = 47mm)
All measurements in Millimeters
Phoenix Gold
A Division of AAMP of America™
13190 56th Court
Clearwater, Florida 33760
P: 866-788-4237
© 2012 AAMP of Florida, Inc
Designed and Engineered in the USA
LIMITED WARRANTY
Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This
warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer in the United States of America only. Should
service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold will (at its discretion), repair or replace the
defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse,
product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not
cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear
and tear is not covered under warranty.
INTERNATIONAL WARRANTIES
Products purchased outside the United States of America are covered only by that country’s Authorized Phoenix Gold reseller and not by Phoenix Gold.
Consumers needing service or warranty information for these products must contact that country’s reseller for information.
|