Pelco Home Security System RM2001SD User Manual

C1957M (3/99)  
RM2001 Series  
VCR Rack Mount  
®
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
1. Installation and servicing should be done by qualified installation and service personnel  
only.  
In North America & Canada:  
Tel (800) 289-9100  
FAX (800) 289-9150  
2. Installation should be done according to all local and national electrical and mechanical  
codes, using only approved materials.  
International Customers:  
Tel (1-559) 292-1981  
FAX (1-559) 348-1120  
3. Use only installation methods and materials capable of supporting four times the  
maximum weight of the VCR and rack mount.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
DESCRIPTION  
The RM2001 Rack Mount holds a single Pelco TLR Series VCR. This versatile rack mount will  
fit any standard 19-inch (48.26 cm) wide console or rack configuration. The RM2001SD model  
is the same as the RM2001, but is supplied with a lockable security door (not installed) having  
a smoked Lexan® window. The rack mounts have a black polyester powder coat finish.  
MODELS  
RM2001  
RM2001SD  
Rack mount for TLR Series VCR. Does not include front door.  
Rack mount for TLR Series VCR. Includes locking front door.  
INSTALLATION  
To install the RM2001 Series VCR Rack Mount:  
NOTE: A security door (item 1),  
backstop bracket (item 2), and  
five 6-32 Phillips screws (item 3)  
are shipped as loose equipment  
for the RM2001SD model (refer  
to Figure 1). The backstop  
Steps 1 and 2 apply to both the RM2001 and RM2001SD VCR Rack Mounts:  
1. Place the rack mount in the console or equipment rack, align the mounting holes, and  
insert and tighten the required fasteners (not supplied).  
2. Set the VCR into the rack mount, pushing it back until it stops at the backstop bracket  
(RM2001 model) or the rear lip of the rack mount base (RM2001SD model).  
bracket should be installed in the  
hole provided in the rear of the  
rack mount base whenever the  
rack mount will be used with-  
out the security door. If the  
backstop bracket is installed  
when using the security door,  
the VCR will protrude and not  
allow the door to close.  
Step 3 applies to the RM2001SD VCR Rack Mount only:  
3. Attach the security door (item 1) to the front of the rack mount with four 6-32 Phillips  
screws (item 3). Refer to Figure 1 and Table A.  
3
SHIPPED LOOSE  
2
2
FOR RM2001SD  
RM2001  
INSTALLED  
FOR RM2001  
Table A. RM2001SD VCR Rack Mount  
Loose Parts List  
Item Qty  
Description  
Security door  
Backstop bracket (see note)  
Phillips screws, 6-32 x 1/4 in.  
1
2
3
1
1
5
3
1
Figure 1. RM2001 Series VCR Rack Mount  
 

Pelco Security Camera C10DN 6X User Manual
Philips Cassette Player AQ 6481 01P User Manual
Philips Digital Photo Frame 6FF3FPB User Manual
Philips DVD Player PET726 User Manual
Philips Styling Iron HP4667 05 User Manual
Polar Heart Rate Monitor F4TM User Manual
Polycom Camera Lens Ceiling DocCam User Manual
Polycom Webcam VSXTM 8000 User Manual
Poulan Chainsaw 115259626 User Manual
Poulan Trimmer GHT 22 User Manual