Peerless Industries Spreader 151 071M User Manual

Great Plains Mfg., Inc.  
Installation Instructions  
6 Foot Drill  
Seed Box Agitator Option  
Used with:  
• 605NT  
When you see this symbol, the subsequent instructions and  
warnings are serious - follow without exception. Your life and  
the lives of others depend on it!  
!
• 3P605NT  
• 3P600  
General Information  
These instructions explain how to install the agita-  
tor option. The agitator stirs the seed directly  
above the metering cups. It is intended to cut  
down on the "bridging" of light fluffy seeds.  
Before You Start  
included in the agitator option packages. Use the  
proper list to inventory parts received.  
These instructions apply to:  
Definitions  
118-748A  
118-749A  
118-750A  
3P600 Agitator w/Drive - 7-1/2"  
3P600 Agitator w/o Drive - 7-1/2"  
3P605NT & 605NT Agitator  
w/Drive  
Right-hand and left-hand as used in this manual  
are determined by facing the direction the ma-  
chine will travel while in use unless otherwise  
stated.  
118-751A  
3P605NT & 605NT Agitator w/o  
Drive  
118-788A  
118-789A  
3P600 Agitator w/Drive - 6"  
3P600 Agitator w/o Drive - 6"  
Manual Update  
Refer to the 6 foot drill operator’s manual for de-  
tailed information on safely operating, adjusting,  
troubleshooting and maintaining the agitator op-  
tion. Refer to the parts manual for part  
identification.  
Drill Manual Part Numbers  
151-061M  
605NT & 3P605NT Operator’s  
Manual  
151-061P  
118-794M  
118-794P  
605NT & 3P605NT Parts Manual  
3P600 Operator’s Manual  
3P600 Parts Manual  
Assembly Instructions  
Agitator Shaft  
1. Remove covers (1) from inside both ends of  
seed box by removing bolt (2), lock washer (3)  
and hex nut (4).  
18726  
Figure 1  
Seed Box Cover Removal  
© Copyright 2000 Printed 4/26/2000  
151-071M  
 
 
Great Plains Mfg., Inc.  
Installation Instructions 3  
Drive Assembly  
605NT and 3P605NT Drive  
NOTE: If your drill is equipped with a native grass  
option, a majority of the agitator drive is already  
installed. Go to page 4 for chain routing.  
1. Mount bearings and flanges (1) to left side of  
drill frame and to the frame support as shown.  
Use 5/16 x 1 inch bolts (2), washers and nuts  
to secure flanges. Leave bolts loose.  
2. Install drive shaft (3) through bearings. As you  
install shaft, place 17 tooth sprocket (4) on  
shaft near left side of drill frame.  
3. Place 17 tooth sprocket (5) on the right end of  
shaft.  
4. Install three 12 tooth idler sprockets (6) in lo-  
cations shown, using a 1/2 x 3-1/2 inch bolts  
(7), hex jam nuts (8), USS flat washers (9)  
and hex flange nuts (10).  
18662  
Figure 3  
605NT & 3P605NT Drive Assembly  
3/31/2004  
151-071M  
 
 
Great Plains Mfg., Inc.  
4
Seed Box Agitator Option  
5. Refer to Figure 4. Install 16 tooth splined  
sprocket (11) to gearbox as shown, and fas-  
ten with snap ring (12).  
6. Route chains as follows:  
a. The 45 pitch chain around new 16 tooth  
sprocket (13) on gearbox to 17 tooth  
sprocket (14).  
b. The 89 pitch chain around 17 tooth  
sprocket (15) near left side of frame to 35  
tooth sprocket (16) on agitator shaft.  
18728  
Figure 4  
7. Adjust idlers to remove chain slack.  
Gearbox Sprocket  
Agitator Chain Routing  
NOTE: For drills with the native grass  
option, include the agitator sprocket  
(16) in the 166 pitch chain routing as  
shown.  
Agitator Chain Routing with Native Grass  
18730  
Figure 5  
151-071M  
3/31/2004  
 
     
Great Plains Mfg., Inc.  
Installation Instructions 5  
3P600 Drive  
3P600 Drive w/Small Seeds Option  
If your drill is equipped with a small seeds option,  
a majority of the agitator drive is already installed.  
1. Mount bearing and flanges (1) inside end  
panels of drill frame. Use 5/16 x 1 inch bolts  
(2), washers and nuts to secure flanges.  
Leave bolts loose.  
• Place 17 tooth sprocket (5) near left drill  
frame end panel.  
2. Install drive shaft (3) through bearings. As you  
install shaft, place 22 tooth sprocket (4) on  
shaft to the left of gearbox.  
• Align sprocket and secure with key (9).  
• Go to step 7b on page 6.  
3. Place 17 tooth sprocket (5) on shaft near the  
left drill frame end panel.  
4. Place 12 tooth splined sprocket (6) on left  
front gearbox shaft. Secure with snap ring (7).  
5. Align shaft and tighten flange bolts. Align  
sprockets (4 and 5). Secure with keys (8 and  
9).  
Figure 6  
18728  
3P600 Drive Assembly  
3/31/2004  
151-071M  
 
 
Great Plains Mfg., Inc.  
6
Seed Box Agitator Option  
6. Install two 12 tooth idler sprockets (10) in lo-  
cations shown, using 1/2 x 3 1/2 inch bolts  
(11), hex jam nuts (12), USS flat washers (13)  
and hex flange nuts (14).  
7. Route chains as follows:  
a. The 63 pitch chain around new 12 tooth  
sprocket (15) on gearbox to 22 tooth  
sprocket (16).  
b. The 68 pitch chain around 17 tooth  
sprocket (17) near left side of frame to 35  
tooth sprocket (18) on agitator shaft.  
18731  
Figure 7  
Idler Installation  
8. Adjust idlers to remove chain slack.  
Figure 8  
3P600 Chain Routing  
18732  
151-071M  
3/31/2004  
 
     
Great Plains Mfg., Inc.  
Installation Instructions 7  
5. Start over with paddle 1 and continue until  
each feeder cup has a paddle. The fully as-  
sembled shaft will have a spiral result.  
Agitator Paddle Installation  
1. Place an agitator paddle (1) over the hex shaft  
directly above a feeder cup. Position paddle  
as shown (paddle 1).  
6. After checking for interference, torque the  
paddle bolts to 9 ft. lbs. (108 in lbs.)  
2. Slip a 1/4 x 2 inch hex flange bolt (2) through  
the paddle and secure with a hex flange lock  
nut (3).  
NOTE: Before tightening a paddle or group of  
paddles, carefully rotate the drive system to make  
sure paddles do not hit the tray dividers.  
3. Place a paddle over the next feeder cup. Ro-  
tate this paddle 1/6th of a turn and slide it onto  
the next set of flats as shown (paddle 2).  
paddle 1  
4. Continue the installation above each feeder  
cup, rotating the paddle 1/6th of a turn each  
time as shown ( paddles 3 through 6).  
paddle 2  
paddle 3  
paddle 4  
paddle 5  
paddle 6  
18739  
Figure 9  
Agitator Paddle Assembly  
3/31/2004  
151-071M  
 
 
Great Plains Mfg., Inc.  
8
Seed Box Agitator Option  
118-748A 3P600 AGITATOR ASSY W/DRIVE - 7-1/2"  
Your kit includes:  
Qty.  
Part No.  
Part Description  
9
2
1
1
1
1
1
2
1
4
2
10  
9
10  
2
9
2
10  
4
1
118-493D  
118-494D  
118-498D  
118-556D  
133-037D  
136-065D  
136-111D  
168-127D  
800-141C  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-100C  
808-160C  
808-170C  
808-185C  
817-025C  
822-040C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL AGITATOR SHAFT  
SGS/AUXILLARY DRIVE SHAFT  
CHAIN RL #40 63 PITCHES  
CHAIN RL #40 68 PITCHES  
3/16 X 1 KEY  
SNAP RING EXT F/PEERLESS G.B.  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13PPLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPROCKET 40B22 3/4B W/K.W. &SS  
SPKT 40B12 X 36T SPLINE BORE  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
NO. 40 12T IDLER SPKT.  
1
1
1
2
2
10  
3
BEARING 3/4BORE 47MM SPHERE OD  
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
3/31/2004  
151-071M  
 
 
Great Plains Mfg., Inc.  
Installation Instructions 9  
118-750A 605NT & 3P605NT AGITATOR ASSY W/DRIVE  
Your kit includes:  
Qty.  
Part No.  
Part Description  
9
2
1
1
1
1
1
1
1
4
3
10  
9
10  
3
9
3
10  
3
2
118-493D  
118-494D  
118-498D  
118-556D  
202-182D  
136-054D  
136-161D  
168-127D  
800-141C  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-170C  
808-185C  
808-271C  
817-025C  
822-040C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL AGITATOR SHAFT  
AUXILLARY DRIVE SHAFT  
CHAIN RL #40 89 PITCHES  
CHAIN RL #40 45 PITCHES  
3/16 X 1 KEY  
SNAP RING EXT F/PEERLESS G.B.  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13 PLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
SPKT 40B16 X 36T SPLINE BORE  
NO. 40 12T IDLER SPKT.  
1
1
3
2
10  
3
BEARING 3/4BORE 47MM SPHERE OD  
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
3/31/2004  
151-071M  
 
Great Plains Mfg., Inc.  
10 Seed Box Agitator Option  
118-749A 3P600 AGITATOR ASSY WITHOUT DRIVE - 7-1/2"  
Your kit includes:  
Qty.  
Part No.  
Part Description  
9
2
1
1
1
1
4
1
6
9
6
1
9
1
6
2
1
1
1
6
3
118-493D  
118-494D  
118-498D  
118-556D  
136-111D  
168-127D  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-170C  
808-185C  
817-025C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL AGITATOR SHAFT  
CHAIN RL #40 68 PITCHES  
3/16 X 1 KEY  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13 PLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
NO. 40 12T IDLER SPKT.  
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
118-751A 605NT & 3P605NT AGITATOR ASSY WITHOUT DRIVE  
Your kit includes:  
Qty.  
Part No.  
Part Description  
9
2
1
1
1
1
4
2
6
9
6
2
9
2
6
2
1
1
2
6
3
118-493D  
118-494D  
118-498D  
118-556D  
136-054D  
168-127D  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-170C  
808-185C  
817-025C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL AGITATOR SHAFT  
CHAIN RL #40 89 PITCHES  
3/16 X 1 KEY  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13 PLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
NO. 40 12T IDLER SPKT.  
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
3/31/2004  
151-071M  
 
Great Plains Mfg., Inc.  
Installation Instructions 11  
118-788A 3P600 AGITATOR ASSY W/DRIVE - 6"  
Your kit includes:  
Qty.  
Part No.  
Part Description  
11  
2
1
1
1
1
1
2
1
118-493D  
118-494D  
118-498D  
118-556D  
133-037D  
136-104D  
136-111D  
168-127D  
800-141C  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-100C  
808-160C  
808-170C  
808-185C  
817-025C  
822-040C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL ADGITATOR SHAFT  
SGS/AUXILLARY DRIVE SHAFT  
CHAIN RL #40 62 PITCHES  
CHAIN RL #40 68 PITCHES  
3/16 X 1 KEY  
SNAP RING EXT F/PEERLESS G.B.  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
4
2
10  
11  
10  
2
11  
2
10  
4
1
1
1
1
2
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13GPLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPKT 40B22 3/4B W/K.W. &SS  
SPKT 40B12 X 36T SPLINE BORE  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
NO. 40 12T IDLER SPKT.  
2
10  
3
BEARING 3/4BORE 47MM SPHERE  
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
3/31/2004  
151-071M  
 
Great Plains Mfg., Inc.  
12 Seed Box Agitator Option  
118-789A 3P600 AGITATOR ASSY WITHOUT DRIVE - 6"  
Your kit includes:  
Qty.  
Part No.  
Part Description  
11  
2
1
1
1
1
4
1
6
11  
6
1
11  
1
6
2
1
1
1
118-493D  
118-494D  
118-498D  
118-556D  
136-111D  
168-127D  
801-035C  
802-039C  
802-282C  
802-448C  
803-008C  
803-036C  
803-088C  
803-169C  
804-009C  
804-017C  
808-170C  
808-185C  
817-025C  
822-041C  
822-128C  
AGITATOR PADDLE 3/4 HEX  
LOCK COLLAR 3/4 HEX BORE  
SEED FLOAT DOWN FLOAT STOP  
6’ DRILL AGITATOR SHAFT  
CHAIN RL #40 68 PITCHES  
3/16 X 1 KEY  
SCREW SET 5/16-18 SKT KP X 3/8  
HHCS 1/2-13X3 GR5  
RHSNB 5/16-18X1 GR5  
HFSS 1/4-20X2 GR5  
NUT HEX 5/16-18 PLT  
NUT HEX JAM 1/2-13 PLT  
NUT HEX LOCK 1/4-20 FLG  
NUT HEX FLG. LOCK 1/2-13 PLT.  
WASHER LOCK SPRING 5/16 PLT  
WASHER FLAT 1/2 USS PLT  
SPKT 40B17 X 3/4BORE W/KW&SS  
SPKT 40B35 X 3/4 HEX BORE  
NO. 40 12T IDLER SPKT.  
6
3
FLANGETTE 47 MST  
BEARING 3/4HEX B 47MM SPHER OD  
3/31/2004  
151-071M  
 

Pentax Binoculars 822 User Manual
Philips Baby Accessories 240BW8 User Manual
Philips Hot Beverage Maker HD4671 User Manual
Philips MP3 Docking Station DS7700 User Manual
Philips MP3 Docking Station DS9800W User Manual
Philips Paper Shredder 6886 User Manual
Pioneer Car Stereo System DEH 1200MP User Manual
Pioneer Stereo Receiver VSX 31 User Manual
Pioneer Stereo System VSX 24TX User Manual
Premio Computer Kitchen Entertainment Center Aries Centella User Manual