Patton electronic IP Phone 4970 4980 4990 User Manual

SmartNode 4970/4980/4990 Series  
Multi-Port T1/E1/PRI  
Enterprise VoIP Gateway,  
Gateway-Router, IAD  
Quick Start Guide  
This is a Class A device and is not intended for use in a residential environment.  
Sales Office: +1 (301) 975-1000  
Part Number: 07MSN4970-80-90-QS, Rev. A  
Revised: May 24, 2012  
Technical Support: +1 (301) 975-1007  
 
Electrostatic Discharge (ESD) can damage equipment and impair electrical  
circuitry. It occurs when electronic printed circuit cards are improperly  
handled and can result in complete or intermittent failures. Do the follow-  
ing to prevent ESD:  
CAUTION  
• Always follow ESD prevention procedures when removing and replac-  
ing cards.  
• Wear an ESD-preventive wrist strap, ensuring that it makes good  
skin contact. Connect the clip to an unpainted surface of the chassis  
frame to safely channel unwanted ESD voltages to ground.  
• To properly guard against ESD damage and shocks, the wrist strap  
and cord must operate effectively. If no wrist strap is available,  
ground yourself by touching the metal part of the chassis.  
1.0 Power up the SmartNode  
1. Insert the barrel type connector end of the AC power cord into the external power supply connector.  
2. Insert the female end of the power cord into the internal power supply connector.  
3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-  
tact Patton to replace it with a compatible power cord.  
4. Connect the male end of the power cord to an appropriate power outlet.  
5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready  
to configure.  
2.0 Configuring your SmartNode  
Refer to the following manuals (available online at www.patton.com/manuals) for detailed information  
about installing, configuring, operating, and troubleshooting the SmartNode:  
SmartNode Model 4970 Series User Manual: www.patton.com/manuals/SN4970.pdf  
SmartNode Model 4980/4990 Series User Manual: www.patton.com/manuals/SN4980-90.pdf  
SmartNode 4970/4980/4990 Series Quick Start Guide  
3
 
A.0 Customer and Technical Support  
Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP client  
Online support: www.patton.com  
E-mail support: [email protected]—answered within 1 business day  
Telephone support:  
Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to  
2200 UTC/GMT)  
Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 9:00 am to 5:30 pm CET (08:00 to 16:30  
UTC/GMT)  
Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)  
B.0 Appendix—Factory default settings  
B.1 SmartNode 4970  
Username:  
Password:  
administrator  
(blank)  
DHCP  
IP Address:  
Network Mask:  
n/a  
B.2 SmartNode 4980 & 4990  
Username:  
administrator  
DHCP  
IP Address (Eth 0/0):  
Network Mask (Eth 0/0): n/a  
IP Address (Eth 0/1):  
192.168.1.1 (DHCP Server)  
Network Mask (Eth 0/1): 255.255.255.0  
4
SmartNode 4970/4980/4990 Series Quick Start Guide  
 
C.0 Compliance Information  
C.1 Compliance  
EMC Compliance:  
EN55022, Class A  
EN55024  
Safety Compliance:  
IEC/EN 60950-1, 2nd edition  
PSTN Compliance:  
ACTA (Part 68)  
IC CS-03  
AS/ACIF S016:2001  
AS/ACIF S038:2001  
ETSI TBR 12, TBR 12/A1 & TBR 13  
TBR 4  
TNA 117: 1992  
TNA 134: 1997  
PTC 220  
SmartNode 4970/4980/4990 Series Quick Start Guide  
5
 
C.2 FCC Part 68 (ACTA) Statement  
This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of  
this equipment is a label that contains—among other information—a product identifier in the format US:  
AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.  
The method used to connect this equipment to the premises wiring and telephone network must comply with the  
applicable FCC Part 68 rules and requirements adopted by the ACTA.  
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that  
temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-  
pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with  
the FCC if you believe it is necessary.  
The telephone company may make changes in its facilities, equipment, operations or procedures that could  
affect the operation of the equipment. If this happens the telephone company will provide advance notice in  
order for you to make necessary modifications to maintain uninterrupted service.  
If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If  
the equipment is causing harm to the telephone network, the telephone company may request that you discon-  
nect the equipment until the problem is resolved.  
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-  
vice commission or corporation commission for information.  
C.3 Industry Canada Notice  
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-  
firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-  
tion was performed based on a Declaration of Conformity indicating that Industry Canada technical speci-  
fications were met. It does not imply that Industry Canada approved the equipment.  
This Declaration of Conformity means that the equipment meets certain telecommunications network protective,  
operational and safety requirements. The Department does not guarantee the equipment will operate to the  
user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to  
the facilities of the local telecommunications company. The equipment must also be installed using an acceptable  
method of connection. In some cases, the company’s inside wiring associated with a single line individual service  
may be extended by means of a certified connector assembly (telephone extension cord). The customer should  
be aware that compliance with the above condition may not prevent degradation of service in some situations.  
Repairs to some certified equipment should be made by an authorized maintenance facility designated by the  
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give  
the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for  
their own protection that the ground connections of the power utility, telephone lines and internal metallic water  
pipe system, are connected together. This protection may be particularly important in rural areas.  
6
SmartNode 4970/4980/4990 Series Quick Start Guide  
 
C.4 CE Declaration of Conformity  
Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele-  
vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility and Directive 2006/95/EC  
relating to electrical equipment designed for use within certain voltage limits. The Declaration of Conformity  
may be obtained from Patton Electronics, Inc at www.patton.com/certifications.  
The safety advice in the documentation accompanying this device shall be obeyed. The conformity to the above  
directive is indicated by CE mark on the device.  
C.5 Authorized European Representative  
D R M Green  
European Compliance Services Limited.  
Avalon House, Marcham Road  
Abingdon,  
Oxon OX14 1UD, UK  
SmartNode 4970/4980/4990 Series Quick Start Guide  
7
 
Copyright statement  
Copyright © 2012, Patton Electronics Company. All rights reserved.  
The information in this document is subject to change without notice. Patton Electronics assumes no  
liability for errors that may appear in this document.  
Trademarks statement  
The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-  
ment are the property of their respective owners.  
Warranty, Trademark, & Compliance Information  
For warranty, trademark and compliance information, refer to the user manual for your SmartNode model,  
available online at www.patton.com/manuals.  
8
SmartNode 4970/4980/4990 Series Quick Start Guide  
 

MTD Lawn Mower 111 902 026 User Manual
Nextar Portable Speaker NS BT007 User Manual
Niles Audio Speaker CM960SUB User Manual
Nilfisk ALTO Pressure Washer 7 FA User Manual
Nilfisk ALTO Vacuum Cleaner GD 10 Back User Manual
Nortel Networks Conference Phone NN 10300 014 User Manual
NuTone Iron AVD50N User Manual
Omron Healthcare Scale HBF 306 User Manual
Palm PDAs Smartphones 405 5566A US User Manual
Patton electronic Network Card 2701RC User Manual