Metra Electronics Automobile Accessories 99 7861 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7861  
APPLICATIONS  
Honda Pilot  
•2003-2008  
•2006-2008 (Without Factory Navigation)  
99-7861  
KIT FEATURES  
• Recessed DIN  
• Pocket  
• ISO Head Unit Provision With Pocket  
KIT COMPONENTS  
A) “LRadio Housing • B) “E” Radio Housing • C) Pocket • D) Rear Support Bracket • E) ISO Brackets  
F) ISO Trimplate • G) (2) # 8x3/8” Phillips Truss Head Screws H) (2) # 8x3/8” Phillips Pan Head Screws  
B
C
A
G
D
E
F
H
WIRING AND ANTENNA CONNECTIONS (Sold Separately)  
Harness:  
• 70-1721 - Honda/Acura harness 1998-up  
Antenna Adapter:  
• 40-HD10 - Honda antenna adapter 2005-up  
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ • Panel Removal Tool • Phillips Screwdriver • Socket Set  
1-800-221-0932  
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION REV. 06-29-09  
 
DASH DISASSEMBLY  
99-7861  
HONDA PILOT 2003-2008  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
Using a small flat blade screwdriver  
remove the blank plate from upper  
right side of radio trim panel.  
(Figure A)  
Unsnap radio trim panel. Unplug  
switches and remove panel.  
(Figure B)  
3
4
B
Remove (4)10mm bolts securing  
radio, unplug and remove radio.  
(Figure C)  
C
1
 
DASH DISASSEMBLY  
99-7861  
HONDA PILOT 2006-2008  
(Without Factory Navigation)  
A
Disconnect the negative battery  
1
terminal to prevent an accidental  
short circuit.  
2
Remove (2) screws from the top  
of the instrument panel trim.  
Unclip and remove the instru-  
ment panel trim. (Figure A)  
Unclip and remove the left center  
trim panel. (Figure B)  
3
4
B
Unclip the radio trim panel.  
Unplug and remove the panel.  
(Figure C)  
5
Remove the (4) screws securing  
the radio. Unplug and remove  
the radio. (Figure D)  
Continue to kit assembly.  
C
D
2
 
KIT ASSEMBLY  
99-7861  
HONDA PILOT  
•2003-2008  
•2006-2008 (Without Factory Navigation)  
1
Select the proper radio housing for  
your vehicle. EX models use radio  
housing (E) and LX models use radio  
housing (L). The radio housings are  
labeled on one of the mounting tabs.  
(Figure A)  
A
Mount the pocket to the back of the  
radio housing with the (2) #8x3/8”  
phillips pan head screws supplied.  
(Notches on the pocket must be on  
top.) (Figure B)  
2
3
B
Mount the rear support bracket to  
the back of the pocket with the (2)  
#8x3/8” Phillips truss head screws  
supplied. (Figure C)  
C
3
 
KIT ASSEMBLY  
99-7861  
DIN HEAD UNIT PROVISION WITH POCKET  
A
Slide DIN cage (supplied with radio)  
into the assembled radio housing  
from the front. (Figure A)  
1
2
3
Secure DIN cage to radio housing by  
bending the locking tabs outward.  
(Figure A)  
Slide the radio into the DIN cage  
until it snaps into place. (Figure B)  
B
4
 
KIT ASSEMBLY  
99-7861  
ISO HEAD UNIT PROVISION WITH POCKET  
A
Align the holes in the ISO brackets  
with the holes in the radio. Mount  
the brackets to the radio using  
screws supplied with the radio.  
(Figure A)  
1
Slide the radio/bracket assembly into  
the assembled radio housing until it  
snaps into place. (Figure B)  
2
3
Snap the ISO trimplate onto the front  
B
of the assembled radio and housing.  
(Figure B)  
NOTE: To remove the radio unsnap  
and remove the ISO trimplate. Using  
a flat blade screwdriver disengage  
ISO brackets from the radio housing  
and slide radio out of radio housing.  
5
 
FINAL ASSEMBLY  
99-7861  
FINAL ASSEMBLY  
A
B
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown.  
(Isolate and individually tape off the ends of any unused wires to prevent  
electrical short circuit.)  
1
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
2
3
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc . . . Red  
Dimmer . . . . . . . . . . Orange / White  
Right Front (+) . . . . . White  
12V Batt / Memory . . Yellow  
Ground . . . . . . . . . . . Black*  
Power Antenna . . . . . Blue  
Left Front (-). . . . . . . White / Black  
Right Rear (+). . . . . . Violet  
Amp Turn-On . . . . . . Blue / White  
Amp Ground . . . . . . . Black / White  
Illumination. . . . . . . . Orange  
Right Rear (-) . . . . . . Violet / Black  
Left Rear (+). . . . . . . Green  
Left Rear (-) . . . . . . . Green / Black  
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
1-800-221-0932  
Rev. 06/29/09  
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION  
INST99-7861  
6
 

Laser Handheld TV DVBT C30 User Manual
Lennox Hearth Stove H8346 DRTRM GV230 NKL User Manual
Life Fitness Exercise Bike 95R IFIXX XX User Manual
Martin Audio Speaker CS265 User Manual
Master Appliance Glue Gun GG 100 User Manual
Master Lock Portable Generator MGY5000 User Manual
Mattel Motorized Toy Car M8487 0920 User Manual
Meade Telescope DS 114AT User Manual
Melissa Toaster 643 106 User Manual
Mellerware Iron 23009GR1200W User Manual